AudioDIWHY
UNITED STATES OF AMERICA • + Follow
Tools, APP Software Used etc.
|
EagleAutodesk
|
Description
1J24B audio experimenters' board
Please see this blog post for more information:
https://audiodiwhy.blogspot.com/2022/02/1j24b-part-ii-expermenters-board.html
The 1J24B pentode is an inexpensive low plate voltage small valve ("tube"); this PCB can assist in adding this tube to your audio design as it provides op amp buffers, power for the tube, and voltage dividers, and of course traces for the tube's grid, cathode, screen, etc., eliminating a lot of the tedium needed to breadboard around the 1J24B.
Schematic and Layout
Github
https://github.com/cslammy/tubetrashexperimenterboard
Feb 14,2022
1,491 views
1J24B audio experimenters' board
Helps designers work with the interesting 1J24B low voltage miniture pentode tube for audio.
1491
0
0
Published: Feb 14,2022
Standard PCB
BOM(Bill of materials)
PCBWay Donate 10% cost To Author
Under the
Attribution-ShareAlike (CC BY-SA)
License.
- Comments(0)
- Likes(0)
Upload photo
You can only upload 5 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
More by AudioDIWHY
-
BNC to Banana x3 adapter board
I needed an easy way to adapt BNC to banana. There are plenty of M < > F adapters out there, b...
-
LFO Mini: CA3080 based LFO
I needed a small PCB for upcoming projects where a Low Frequency Oscillator will be required. I also...
-
LFO2 From "Electronics For Musicians"
Analog LFO with variable frequency and lots of modulation options based on an EFM ("Electronics for ...
-
JTAG to SWD Converter
Simple JTAG to SWD adapter.My use case is Segger J-LINK EDU MINI to Raspberry Pi Pico but this board...
-
Rotary Encoder Experimenter's Dev Board
UPDATE: new revision 9-29-24 posted. Lower parts count, more reliable software debouncing for the en...
-
Bench 4x2 Bluetooth Mixer
Simple 14HP Eurorack 4x2 synth mixer.outputs are 2x 100mil terminal posts on rear of PCB.You will ne...
-
Anything to Clock--LM311 based
I needed a simple circuit to condition incoming signals so a MCU could read them as clock:--rectify ...
-
Vactrol Based Audio Envelope Follower
An audio envelope follower based on a 5C3 Vactrol. Useful for auto-wah (send its output to a bandpas...
-
Warm Floater Eurorack Power Extender
I ran out of physical connections on my Eurorack Power supply. This PCB supplies 1 input and 3 outpu...
-
"KiCADSR" Euro Envelope Generator
This is my first project using KiCAD for EDA instead of Autodesk Eagle.I wanted to see if I had the ...
-
Low Noise Preamp based on Arp 2600 Synthesizer
The Arp 2600 synthesizer has a preamp that takes an unbalanced signal and amplifies it 10x, 100x, an...
-
Arp 2600 clone--inverter-mixer
The ARP2600 is a legendary, classic semi-modular analog synthesizer. Its voltage processor circuitr...
-
SEEED XAIO RP2040 ADC and Buffer Board
The SEEED XAIO RP2040 is a fantastic little dev board, featuring the RP2040 MCU.I needed a buffered ...
-
Dual LFO daughterboard
I needed a small Dual LFO (2 independent LFO's on a single PCB) for future projects. This PCB is bas...
-
CV Generator
A 3x CV Generator for synthesizers. Outputs are -10 to +10V DC with about 20mA source/sink current. ...
-
BNC to 3.5mm x3 adapter board
I needed some BNC to 3.5mm conversion and didn't want to use unreliable and fragile adapters or cust...
-
Voltage Controlled Stereo Panner
This is a modular synthesizer stereo panner for audio or control voltages.This is a modular project ...
-
Dual Concentric Pots to 4x JST XH 3 pin males
Needed an easy way to add dual concentric pots to my project. The PCB featured here accommodates 2 c...
You may also like
-
-
-
-
Tester for Touch Screen Digitizer without using microcontroller
270 2 2 -
Audio reactive glow LED wristband/bracelet with NFC / RFID-Tags
258 0 1 -
-
-
