YZ 1-50 | The Desktop Robotics Initiative

About Me

I am Md Rakibul Hasan Yorozaki, an independent designer and roboticist based in Philadelphia, USA. I started YZ Labs as a one-person research initiative to explore how advanced technologies can be made more accessible through 3D printing, affordable electronics and practical engineering. The YZ 1-50 is the first project in this journey.



The YZ 1-50

The YZ 1-50 is a functional six-axis desktop robotic arm that brings the mechanical configuration of an industrial robot to an accessible scale.

  • 58 3D-printed PLA components
  • Six Feetech STS3215 bus servos
  • Belt-driven base, shoulder and elbow joints
  • Three direct-drive wrist modules
  • 100 g design payload
  • Interchangeable end effectors
  • Dedicated Windows application with inverse kinematics, collision checking and torque limits



The arm was developed through a parametric design workflow, allowing mechanical interference, alignment, torque requirements and printability to be evaluated before fabrication. Since September, I have published 29 research log entries documenting its development, including mechanical failures and the engineering decisions behind their solutions.



Project film: https://www.yz-labs.com/home.html

From Five Modules to One PCB

The arm currently operates using five separate electronic modules connected inside its base. Although functional, this configuration introduces unnecessary wiring, occupies valuable space and lacks current-monitoring capabilities.



To address these limitations, I designed a dedicated 100 × 80 mm four-layer controller that consolidates the entire electronic system into one PCB, positioned directly beneath the base pulley.



The controller incorporates:

  • ESP32-S3-WROOM-1 with native USB-C
  • Half-duplex servo bus communication
  • Integrated 5 V and 3.3 V power regulation
  • INA226 current monitoring with a 5 mΩ shunt
  • Fuse, transient and reverse-polarity protection
  • Hall sensor inputs and emergency stop interface
  • LED lighting control and end-effector connectivity
  • Nine additional GPIOs for future development
  • Current monitoring is particularly important, as it will allow me to explore protective torque shutdown during mechanical overloads and develop a more reliable robotic system.



The Engineering Challenge

The initial two-layer PCB passed ERC and DRC but revealed significant limitations in its high-current distribution. Further analysis identified eighteen potentially restrictive connections across the power supply and ground return paths.

I subsequently redesigned the controller as a four-layer PCB with dedicated ground and power planes, approximately 430 stitching vias and improved current distribution.



The revised design has been evaluated for continuous servo supply currents of approximately 5 A or greater. Physical testing will validate these calculations and the board's thermal performance.

The manufacturing files, schematic, BOM with LCSC component numbers and placement files are ready, with ERC completed successfully and only silkscreen-related DRC warnings remaining.



What PCBWay's Sponsorship Would Enable

The robotic arm is already operational. The next milestone is bringing its dedicated controller to life.

I would be grateful for PCBWay's support in manufacturing five four-layer PCBs with SMD assembly, with through-hole components supplied separately for manual assembly.

These boards would allow me to test power regulation, servo communication, current monitoring, overload protection and sensor integration before expanding the arm's capabilities with force-sensing grippers and interchangeable tools.

In return, I would offer:

  • PCBWay recognition on the YZ Labs website and public component list.
  • Dedicated research entries documenting PCB integration and measured performance.
  • PCBWay branding in project films and technical videos.
  • A 20–30-second demonstration video for PCBWay's channels.
  • Publication on PCBWay's sponsored projects platform.

Beyond completing the YZ 1-50, I hope to create more educational videos and tutorials that help other makers explore robotics, electronics and custom PCB development.

My next project will be a 3D-printed bionic arm, building upon the knowledge gained through this work. I hope PCBWay can become part of this journey as I continue learning, building and sharing accessible technologies.


Yorozaki | YZ Labs

Philadelphia, USA

https://www.yz-labs.com

Apply for sponsorship >>
13800+ Projects Sponsored
Nov 17,2026
12 viewsReport item
  • Comments(0)
  • Likes(0)
Upload photo
You can only upload 5 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000