|
KiCADKicad
|
usb_ch341_e22p
USB → SPI adapter for using an EBYTE E22P-868M30S LoRa module (SX1262 + PA, 30 dBm / 1 W) with meshtasticd on a PC or a Raspberry Pi, with no GPIO needed.
The bridge is a CH341F in UIO mode, the mode supported by Meshtastic's libch341-spi-userspace driver. A TPS2115A power multiplexer switches automatically between USB power and a DC jack, so the module can transmit at full power without overloading the computer's port.
How the power path works
This is the least obvious part of the design. The E22P draws 600–670 mA when transmitting at 30 dBm, more than a USB port guarantees (500 mA). The board handles this with a multiplexer whose source selection is deterministic, not based on comparing voltages
D0 is tied to ground and D1 is driven by the jack's switch contact, with R7 (10 kΩ) pulled up to VBUS. So D1 encodes "jack present and USB present", which gives two useful properties:
With the jack plugged in, the jack always wins, whichever source has the higher voltage (both useful rows use D0=0, where the TPS2115A truth table ignores the IN2>IN1 comparison).
Without USB the module is left unpowered, which is intended: the board is useless when disconnected from the host, and this prevents a powered E22P from back-feeding current through the pins of an unpowered CH341.
LED D4 hangs off STAT, which is open-drain and pulls low when IN1 is active: on = running from the jack.
usb_ch341_e22p
Project images are for reference only. Actual production is based on the manufacturing files on the project page.
Please review the designer's notes (e.g., PCB thickness) and select the appropriate options.
PCBWay is not responsible
for issues caused by unsuitable parameter selections.
For more important ordering information, please refer to
Read More
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen(Without Speaker)
BUY NOW- Comments(0)
- Likes(0)
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Carlos Valdes
-
LM20MeshNode V2
Pocket Meshtastic node built around the Nordic nRF54LM20A (Minew ME54BS13 module), with a Minew MS21...
-
INA350_Nucleo-64_Hat
INA350 Nucleo-64 HatTest board that plugs onto an STM32 NUCLEO-64 through the morpho connectors. It ...
-
BY1515Controller_Nucleo-64_Hat
BY1515 Controller Nucleo-64 HatAdd-on board for an STM32 NUCLEO-64 (designed for the NUCLEO-G474RE) ...
-
usb_ch341_e22p
USB → SPI adapter for using an EBYTE E22P-868M30S LoRa module (SX1262 + PA, 30 dBm / 1 W) with mesht...
-
Wiznet_5500_EVB_Pico2_E22P
A custom PCB carrier board built around the WIZnet W5500-EVB-Pico2 (an RP2350 with an on-board W5500...
-
E80-900M2213S_SE050_Breakout
A breakout board for the Ebyte E80 family of 16 × 26 mm dual-band LoRa modules (sub-GHz and 2.4 GHz)...
-
LM20MeshNode
LM20MeshNodePocket Meshtastic node built around the Nordic nRF54LM20A (Minew ME54BS13 module), with ...
-
Multiple IMU Breakout Board
What is it about?This board is the first piece of hardware for AI MotoLogger, a data logger I'm desi...
-
Rpi3FanHatPlus
Rpi3FanHatPlusRaspberry Pi 5 HAT+ that drives the three fans of a case with a Microchip EMC2303 fan ...
-
NXP SE050 Secure Element Breakout Board
A minimal breakout board for the NXP EdgeLock SE050E2HQ1 secure element, bringing the I²C interface ...
-
-
-
-
BorePilot - ESP32-S3 Smart Borewell Pump Controller
340 0 0 -
-
-
AudioLink – USB & Bluetooth LE Audio / Auracast Receiver with Balanced Line Outputs (nRF5340)
487 0 1 -
-
-
-
Émetteur Récepteur Optique Expérimental (communication UART ATtiny + fibre optique)
475 0 1 -







