|
KiCADKicad
|
BY1515Controller_Nucleo-64_Hat
BY1515 Controller Nucleo-64 Hat
Add-on board for an STM32 NUCLEO-64 (designed for the NUCLEO-G474RE) that lets the Nucleo control a BY-1515 hot plate (500 W, 150 × 150 mm plate, as used for SMD preheating and reflow). It measures the plate with two isolated K-type thermocouple inputs and switches the heater through the hot plate's own triac stage. This board carries no mains voltage.
How it controls the hot plate
Inside the BY-1515, the original controller fires a BTA16 triac through a MOC3063 zero-crossing opto-triac. The MOC3063 LED is fed from a micro pin through a 330 Ω resistor (R12 on the hot plate board).
This hat adds a PhotoMOS relay (U6, AQY212GS) in series with that LED, through a 2-wire cable (J3) and a connector fitted inside the hot plate:
The plate heats only when both the original controller and the Nucleo ask for heat. Set the original controller to on/off mode with a safe maximum temperature, and it keeps working as an independent over-temperature cut-off.
The 230 V side of the hot plate is not modified. A jumper on that internal connector restores the original behaviour; with nothing plugged in, the plate never heats.
The PhotoMOS keeps the Nucleo galvanically isolated from the hot plate electronics.
Fail-safe drive. The PhotoMOS LED is powered by a diode charge pump fed with a 10 kHz PWM signal (PC7, TIM3_CH2). The plate heats only while the firmware keeps that PWM running. A pin stuck high or low, a reset or a crashed firmware turns the heater off. The AQY212GS allows about 5 switching operations per second, so the firmware uses time-proportional control with 1 s windows.
Features
Two isolated K-type thermocouple inputs (J4 TC1, J5 TC2), each with a MAX31856 (U4, U5).
Isolated domain powered by a B0505S-1WR3 DC-DC module (U1) and a TLV76701 LDO (U2).
SPI crosses the barrier through an ISO7761 digital isolator (U3).
Isolation is needed because the BY-1515 plate is earthed and its ring-terminal thermocouple touches the plate, while the MAX31856 needs a floating measurement.
Clearance of at least 3.6 mm between domains on all copper layers. This is functional isolation, not safety isolation.
Heater output to the hot plate (J3) through the PhotoMOS, with a blue HEATING LED (LED1) driven by the same transistor (hardware indication).
12 V fan output (J6): low-side AO3400A (Q3) with SS14 flyback diode, PWM controlled. 12 V comes in through a DC jack (J7).
Buzzer (BZ1, MLT-8530 magnetic) driven by an AO3400A (Q4), PWM controlled.
Green STATUS LED (LED2).
Test points on the isolated side, including FAULT and DRDY of both MAX31856. These signals do not cross the isolator; the firmware reads the fault register instead.
Board
70 × 53 mm, 4 layers, 1.6 mm, green solder mask. Same outline as the INA350 Nucleo-64 Hat.
2×19 sockets (HC-PM254-8.5H) on the bottom side; the board sits about 11 mm above the Nucleo.
Two 3 mm notches on the top edge leave room for the Nucleo user and reset buttons (B1/B2).
J3–J6 are 2.54 mm holes for pin headers or soldered wires. J3, J4 and J5: pin 1 on the right. J6: pin 1 (+12 V) on the left.
Nucleo pin mapping
Signal Morpho pin MCU pin Arduino Use
SCK CN10-31 PB3 D3 SPI1_SCK
SDI (MOSI) CN10-15 PA7 D11 SPI1_MOSI
SDO (MISO) CN10-13 PA6 D12 SPI1_MISO
CS1, thermocouple 1 CN10-17 PB6 D10 GPIO
CS2, thermocouple 2 CN10-29 PB5 D4 GPIO
BOMBA, heater charge pump CN10-19 PC7 D9 TIM3_CH2, 10 kHz
FAN_PWM CN10-25 PB10 D6 TIM2_CH3
ZUMB_PWM, buzzer CN10-23 PA8 D7 TIM1_CH1
LED_EST, status LED CN10-21 PA9 D8 GPIO
LIBRE, spare CN10-33 PA10 D2 test point
+5V (isolated DC-DC supply) CN7-18
+3V3 CN7-16 GND CN7-8/19/20/22, CN10-9/20
Some net names are in Spanish: BOMBA = pump, ZUMB = buzzer, LED_EST = status LED, LIBRE = spare, VENTILADOR = fan.
Repository layout
kicad/ KiCad 10 project (schematic, PCB, design rules)
kicad/lib/ project libraries: symbols, footprints and 3D models used by the board
fabrication/2026-11-17_rev0.1/ Gerbers + drill files (folder and zip), BOM, pick-and-place
images/ README images
Open kicad/BY1515_NUCLEO.kicad_pro with KiCad 10.0 or newer. The .kicad_dru file holds the custom rules for the isolation barrier.
Manufacturing notes
BY1515_NUCLEO_gerbers.zip is ready to upload to a PCB fab (4 layers, 1.6 mm).
The pick-and-place file lists the SMD parts only. The sockets (J1, J2), J3–J7 and U1 are not in it and are soldered by hand.
Fine-pitch parts use _PCBWay footprint variants (solder-mask web ≥ 0.19 mm between pads).
⚠️ Safety
The BY-1515 runs from mains voltage and reaches 400 °C. Fitting the J3 connector means opening the hot plate: do it unplugged, keep the original controller as an over-temperature cut-off, and never leave the plate unattended. You do this at your own risk.
BY1515Controller_Nucleo-64_Hat
Project images are for reference only. Actual production is based on the manufacturing files on the project page.
Please review the designer's notes (e.g., PCB thickness) and select the appropriate options.
PCBWay is not responsible
for issues caused by unsuitable parameter selections.
For more important ordering information, please refer to
Read More
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen(Without Speaker)
BUY NOW- Comments(0)
- Likes(0)
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Carlos Valdes
-
LM20MeshNode V2
Pocket Meshtastic node built around the Nordic nRF54LM20A (Minew ME54BS13 module), with a Minew MS21...
-
INA350_Nucleo-64_Hat
INA350 Nucleo-64 HatTest board that plugs onto an STM32 NUCLEO-64 through the morpho connectors. It ...
-
BY1515Controller_Nucleo-64_Hat
BY1515 Controller Nucleo-64 HatAdd-on board for an STM32 NUCLEO-64 (designed for the NUCLEO-G474RE) ...
-
usb_ch341_e22p
USB → SPI adapter for using an EBYTE E22P-868M30S LoRa module (SX1262 + PA, 30 dBm / 1 W) with mesht...
-
Wiznet_5500_EVB_Pico2_E22P
A custom PCB carrier board built around the WIZnet W5500-EVB-Pico2 (an RP2350 with an on-board W5500...
-
E80-900M2213S_SE050_Breakout
A breakout board for the Ebyte E80 family of 16 × 26 mm dual-band LoRa modules (sub-GHz and 2.4 GHz)...
-
LM20MeshNode
LM20MeshNodePocket Meshtastic node built around the Nordic nRF54LM20A (Minew ME54BS13 module), with ...
-
Multiple IMU Breakout Board
What is it about?This board is the first piece of hardware for AI MotoLogger, a data logger I'm desi...
-
Rpi3FanHatPlus
Rpi3FanHatPlusRaspberry Pi 5 HAT+ that drives the three fans of a case with a Microchip EMC2303 fan ...
-
NXP SE050 Secure Element Breakout Board
A minimal breakout board for the NXP EdgeLock SE050E2HQ1 secure element, bringing the I²C interface ...
-
-
-
-
BorePilot - ESP32-S3 Smart Borewell Pump Controller
340 0 0 -
-
-
AudioLink – USB & Bluetooth LE Audio / Auracast Receiver with Balanced Line Outputs (nRF5340)
487 0 1 -
-
-
-
Émetteur Récepteur Optique Expérimental (communication UART ATtiny + fibre optique)
475 0 1 -







