|
KiCADKicad
|
INA350_Nucleo-64_Hat
INA350 Nucleo-64 Hat
Test board that plugs onto an STM32 NUCLEO-64 through the morpho connectors. It compares three instrumentation amplifiers measuring the same current shunt:
TI INA350CDS (U8)
Analog Devices AD8220 (U6)
Microchip MCP6N11-010 (U7)
The board reproduces one range of a current-measurement front end (shunt, bypass MOSFET and protection). The three amplifiers can then be compared on real hardware before choosing one for a power-measurement module. No oscilloscope is needed: the Nucleo is meant to sample the three outputs at the same time with its own ADCs, synchronised with a load-step timer, and send the results over USB.
Features
Three amplifier channels (rows A, B, C) on one 4.99 kΩ 0.1 % shunt (R11, between VM and VOUT), each with its own Kelvin connection to the shunt.
Shunt bypass MOSFET (Q1, AO3400A) driven by a UCC27524 gate driver (U4), controlled by the Nucleo.
Loads on VOUT selected with jumpers JP2–JP6, including a step load (Q2 + R16 33 Ω, about 100 mA at 3.3 V) switched by a timer output.
Programmable measured voltage VM: adjustable TLV76701 LDO with the Nucleo DAC injected into its feedback (about 0.8 V to 5.3 V). Open JP1 to feed an external VM on J2 instead.
Local rails from 12 V: +10V_G and +5V5_A (TLV76701 LDOs). A TLV9002 buffers the 0.30 V amplifier reference and VOUT.
12 V input through a DC jack (J5) or a 2-pin header (J1), with an SS34 series diode and a 470 µF bulk capacitor.
Test points on every relevant node and six jumpers to configure the channels.
Board
70 × 53 mm, 4 layers (In1 power, In2 signal), green solder mask.
2×19 sockets (HC-PM254-8.5H) on the bottom side; the board sits about 11 mm above the Nucleo.
Two 3 mm notches on the top edge leave room for the Nucleo user and reset buttons (B1/B2).
Fine-pitch parts use _PCBWay footprint variants (solder-mask web ≥ 0.19 mm between pads).
Compatible Nucleo boards
BoardNotesNUCLEO-G474RE (MB1367)Move JP8 to [2-3] so that VREF+ = VDD. With the factory VREF+ of 2.5 V the full output range does not fit.NUCLEO-G564RE (MB2067)Works as is. The DAC output is on PA5 instead of PA4.
No solder bridges need to be changed on either board.
Nucleo pin mapping
Signal Morpho pin MCU pin Use
O_A, AD8220 output CN7-30 PA1 ADC / COMP1
O_B, MCP6N11-010 output CN7-28 PA0 ADC / COMP3
O_C, INA350 output CN7-34 PB0 ADC / COMP4
DAC_VM, VM setpoint CN7-32 PA4 (G474RE) / PA5 (G564RE) DAC
VOUT_S, output voltage sense CN7-36 PC1 ADC
VM_S, VM sense CN7-38 PC0 ADC
LOAD, load step CN10-31 PB3 TIM2_CH2
BYP0, shunt bypass CN10-5 PB9 GPIO
+3V3 CN7-16
GND CN7-8/19/20/22, CN10-9/20
Repository layout
kicad/ KiCad 10 project (schematic, PCB, design rules)
kicad/lib/ project libraries: symbols, footprints and 3D models used by the board
fabrication/2026-11-17_rev0.1/ Gerbers + drill files (folder and zip), BOM, pick-and-place
images/ README images
Open kicad/PRUEBA_INA.kicad_pro with KiCad 10.0 or newer. The project keeps its original internal name (PRUEBA_INA, Spanish for "INA test"). Part of the schematic text is in Spanish.
Manufacturing notes
PRUEBA_INA_gerbers.zip is ready to upload to a PCB fab (4 layers, 1.6 mm).
The BOM lists LCSC part numbers where available. Generic 0603 passives have no part number.
Test points are pads only and are not in the BOM.
INA350_Nucleo-64_Hat
Project images are for reference only. Actual production is based on the manufacturing files on the project page.
Please review the designer's notes (e.g., PCB thickness) and select the appropriate options.
PCBWay is not responsible
for issues caused by unsuitable parameter selections.
For more important ordering information, please refer to
Read More
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen(Without Speaker)
BUY NOW- Comments(0)
- Likes(0)
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Carlos Valdes
-
LM20MeshNode V2
Pocket Meshtastic node built around the Nordic nRF54LM20A (Minew ME54BS13 module), with a Minew MS21...
-
INA350_Nucleo-64_Hat
INA350 Nucleo-64 HatTest board that plugs onto an STM32 NUCLEO-64 through the morpho connectors. It ...
-
BY1515Controller_Nucleo-64_Hat
BY1515 Controller Nucleo-64 HatAdd-on board for an STM32 NUCLEO-64 (designed for the NUCLEO-G474RE) ...
-
usb_ch341_e22p
USB → SPI adapter for using an EBYTE E22P-868M30S LoRa module (SX1262 + PA, 30 dBm / 1 W) with mesht...
-
Wiznet_5500_EVB_Pico2_E22P
A custom PCB carrier board built around the WIZnet W5500-EVB-Pico2 (an RP2350 with an on-board W5500...
-
E80-900M2213S_SE050_Breakout
A breakout board for the Ebyte E80 family of 16 × 26 mm dual-band LoRa modules (sub-GHz and 2.4 GHz)...
-
LM20MeshNode
LM20MeshNodePocket Meshtastic node built around the Nordic nRF54LM20A (Minew ME54BS13 module), with ...
-
Multiple IMU Breakout Board
What is it about?This board is the first piece of hardware for AI MotoLogger, a data logger I'm desi...
-
Rpi3FanHatPlus
Rpi3FanHatPlusRaspberry Pi 5 HAT+ that drives the three fans of a case with a Microchip EMC2303 fan ...
-
NXP SE050 Secure Element Breakout Board
A minimal breakout board for the NXP EdgeLock SE050E2HQ1 secure element, bringing the I²C interface ...
-
-
-
-
BorePilot - ESP32-S3 Smart Borewell Pump Controller
340 0 0 -
-
-
AudioLink – USB & Bluetooth LE Audio / Auracast Receiver with Balanced Line Outputs (nRF5340)
487 0 1 -
-
-
-
Émetteur Récepteur Optique Expérimental (communication UART ATtiny + fibre optique)
475 0 1 -







