i_bell
UNITED STATES OF AMERICA • + Follow
Edit Project
Components
|
FTDI 240XS |
x 1 |
Description
USB OP-AMP Buffer Driver
USB FTDI 240XS 8 BIT I/O, connected to 4 dual op amps as level shifters. TLV2372 Dual OP-amp 3-MHz Rail to Rail
Using FTDI's API calls it is easy to find the device (use FTDI_PROG to rename it) Then just send a value in HEX and the chip will drive the op-amps.
By jumping J4 left to center you can use the USB's 5 volts to power the rail to rail op-amps.
You can install a TO-92 regulator at U6 and power it from J5 or J3, and jump J4 from center to right, just not at the same time.
On the bottom of the PCB, I put 0603 footprints, if you need to change the outputs to a lower voltage than 3.3 volts.
Jun 11,2020
1,123 views
USB OP-AMP Buffer Driver
2 Layers PCB 76.2 x 25.4 mm FR-4, 1.6 mm, 1, HASL with lead, Green Solder Mask, White silkscreen
FTDI 240XS 8 BIT IC driving op-amps for level shifting.
1123
0
0
Published: Jun 11,2020
BOM(Bill of materials)
Purchase
Donation Received ($)
PCBWay Donate 10% cost To Author
Only PCB
PCB+Assembly
*PCBWay community is a shared platform and we are not responsible for any design issues.
Copy this HTML into your page to embed a link to order this shared project
Copy
Under the
Attribution-ShareAlike (CC BY-SA)
License.
- Comments(0)
- Likes(0)
You can only upload 1 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
Remove
It looks like you have not written anything. Please add a comment and try again.
View More
View More
VOTING
0 votes
- 0 USER VOTES
0.00
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Design
1/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Usability
2/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Creativity
3/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Content
4/4
More by i_bell
- USB OP-AMP Buffer Driver USB FTDI 240XS 8 BIT I/O, connected to 4 dual op amps as level shifters. TLV2372 Dual OP-amp 3-MHz ...
- USB controled 1 of 16 relays This is and update to a 1 of 16 MUX. I switched to relays so I can connect it to DVM and measure Ohm...
- 1 of 4 RF switch USB Controlled I am hoping this works out, it is my first attempt with PCB way with a non-FR4 board material. Stirp...
- 1 of 16 USB controled Mux for O'Sope or Meter ### DESCRIPTION1 of 16 MUX for oscilloscope, with a 10X probe on the PCB. The Layout can support a T...
- 2 Line, Quad, 1 inch, 7 segment Displays ### DESCRIPTION2 Line, shift out, 4 digit, 1 inch 7 segment displays.### TECHNICAL DETAILS / COMPONE...
You may also like
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
467 0 0 -
RF Control training board for students based on ESP32 C3
618 0 2 -
Aquarius+ Computer, Standard PCB
831 0 4 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
577 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
504 0 1 -
Nintendo Famicom HVC-001 Controller Shells
599 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
560 0 4 -
COMMODORE 128 15KHz DISPLAY ADAPTER (C128 80 COLUMN ADAPTER)
755 1 5 -