Analog to Digitial Converter (ADC) 14 bit SPI breakout board based on MCP33151
I needed an inexpensive SPI based breakout board for 14 bit ADC. This higher resolution is for an audio Volt per octave board, where 12 bits wasn't accurate enough.
I couldn't find any affordable ADC BoBs beyond 12 bits so I drew one up myself.
In short, the MCP33151 is a great choice for makers: it is inexpensive, easy to use, and super easy to program.
The BoB in this project has necessary 1206 SMD filter capacitors and fits into a 14 pin DIP socket. The main IC is MSOP so some familiarity with soldering SMD parts is necessary.
Want to read more about this BoB? Blog post is about the project is here:
https://audiodiwhy.blogspot.com/2022/11/mcp33151-14-bit-adc-breakout-board.html
Analog to Digitial Converter (ADC) 14 bit SPI breakout board based on MCP33151
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen（Without Speaker）
BUY NOW
- Comments(0)
- Likes(0)
More by Audio DIWHY
-
BNC to Banana x3 adapter board
I needed an easy way to adapt BNC to banana. There are plenty of M < > F adapters out there, b...
-
LFO Mini: CA3080 based LFO
I needed a small PCB for upcoming projects where a Low Frequency Oscillator will be required. I also...
-
LFO2 From "Electronics For Musicians"
Analog LFO with variable frequency and lots of modulation options based on an EFM ("Electronics for ...
-
JTAG to SWD Converter
Simple JTAG to SWD adapter.My use case is Segger J-LINK EDU MINI to Raspberry Pi Pico but this board...
-
Rotary Encoder Experimenter's Dev Board
UPDATE: new revision 9-29-24 posted. Lower parts count, more reliable software debouncing for the en...
-
Bench 4x2 Bluetooth Mixer
Simple 14HP Eurorack 4x2 synth mixer.outputs are 2x 100mil terminal posts on rear of PCB.You will ne...
-
Anything to Clock--LM311 based
I needed a simple circuit to condition incoming signals so a MCU could read them as clock:--rectify ...
-
Vactrol Based Audio Envelope Follower
An audio envelope follower based on a 5C3 Vactrol. Useful for auto-wah (send its output to a bandpas...
-
Warm Floater Eurorack Power Extender
I ran out of physical connections on my Eurorack Power supply. This PCB supplies 1 input and 3 outpu...
-
"KiCADSR" Euro Envelope Generator
This is my first project using KiCAD for EDA instead of Autodesk Eagle.I wanted to see if I had the ...
-
Low Noise Preamp based on Arp 2600 Synthesizer
The Arp 2600 synthesizer has a preamp that takes an unbalanced signal and amplifies it 10x, 100x, an...
-
Arp 2600 clone--inverter-mixer
The ARP2600 is a legendary, classic semi-modular analog synthesizer. Its voltage processor circuitr...
-
SEEED XAIO RP2040 ADC and Buffer Board
The SEEED XAIO RP2040 is a fantastic little dev board, featuring the RP2040 MCU.I needed a buffered ...
-
BNC to dual 3.5mm jacks x3
This is a revision of the media adapter boards I've posted--a variation of this one for instance: ht...
-
Dual LFO daughterboard
I needed a small Dual LFO (2 independent LFO's on a single PCB) for future projects. This PCB is bas...
-
CV Generator
A 3x CV Generator for synthesizers. Outputs are -10 to +10V DC with about 20mA source/sink current. ...
-
BNC to 3.5mm x3 adapter board
I needed some BNC to 3.5mm conversion and didn't want to use unreliable and fragile adapters or cust...
-
Voltage Controlled Stereo Panner
This is a modular synthesizer stereo panner for audio or control voltages.This is a modular project ...
-
ARPS-2 – Arduino-Compatible Robot Project Shield for Arduino UNO
355 0 0 -
A Compact Charging Breakout Board For Waveshare ESP32-C3
700 3 6 -
AI-driven LoRa & LLM-enabled Kiosk & Food Delivery System
681 2 0 -
-
-
-
ESP32-C3 BLE Keyboard - Battery Powered with USB-C Charging
897 0 1 -
-
mammoth-3D SLM Voron Toolhead – Manual Drill & Tap Edition
776 0 1
