|
KiCad 8.0KiCad
|
SPI bus isolator
I needed a galvanically separated SPI interface between an ESP32 and an OLED display board.
The voltage output of the convertor can be selected by a jumper between 3V3 and 5V for the OLED board.
The RST signal is not passed through, but recreated at the OLED board side to provide a power-up reset.
The board can be inserted in-between the bus from the CPU to the OLED display board.
This board can be used in other SPI bus situations.
The input and output connector can be selected to suit your particular situation and can be mounted on both sides of the board.
SPI bus isolator
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(0)
More by Paul Versteeg
-
Diff Probe Power Supply (switching)
This is yet another power supply option for the differential probe.https://www.pcbway.com/project/sh...
-
Modifying a Hotplate to a Reflow Solder Station
This is a project to modify a UYUE 946C model hotplate and convert it to a reflow soldering station....
-
Dedicated Power Supply for the DIY rebuild of the Tektronix SG505 sine wave generator
This is a project to build a low noise, dedicated power supply for the very low distortion Tektronix...
-
DIY Rebuild of the Tektronix SG505 high precision, low distortion sine wave generator
This is a DIY project to rebuild the Tektronix SG505 high precision very low distortion sine wave ge...
-
Diff Probe Power Supply (Discrete)
This is a companion Daughter Board power supply for the new 10MHz and 1MHz differential probes liste...
-
Diff Probe Power Supply (VREG-SOIC-8)
This is a daughter board for the new 100MHz differential probe listed in the Shared Projects.It supp...
-
A new 100MHz differential probe
This is a DIY 100MHz version of a new differential probe that was mostly designed by my friend Bud B...
-
LORA-based Mailbox alarm
This information can be used to build a LORA-based mailbox receiver and a sender, using the same PCB...
-
SPI bus isolator
I needed a galvanically separated SPI interface between an ESP32 and an OLED display board.The volta...
-
DiY Dynamic DC Load - Back Plate (3 of 3)
This is the Back Plate/Back Panel for a DIY Dynamic Load instrument
-
DIY Dynamic DC Load - Face Plate (2 of 3)
This is the Face Plate/Front Panel for a DIY DC Dynamic Load instrument
-
DIY Dynamic DC Load (1 of 3)
This is a DIY Dynamic Load instrument that can do many things professional instruments can do too.It...
-
10MHz OCXO frequency reference 2 of 2
This is the front panel PCB used for the 10MHz frequency reference.More details can be found on my B...
-
10MHz OCXO frequency reference 1 of 2
This is part of a 10MHz frequency reference that is based on an OCXO.The project is described in det...
-
10MHz GPSDO V4.1 (4 of 4)
This is the front panel for a high precision GPSDO ( GPS (GNSS) Disciplined Oscillator) with an outp...
-
10MHz GPSDO V4.1 (3 of 4)
This is the front panel for a high precision GPSDO ( GPS (GNSS) Disciplined Oscillator) with an outp...
-
10MHZ GPSDO V4.1 (2 of 4)
This is the output and interface board for a high precision GPSDO ( GPS (GNSS) Disciplined Oscillato...
-
10MHz GPSDO V4.2 (1 of 4)
This is a high precision GPSDO ( GPS (GNSS) Disciplined Oscillator) with an output frequency of 10MH...
-
-
-
-
Tester for Touch Screen Digitizer without using microcontroller
232 2 2 -
Audio reactive glow LED wristband/bracelet with NFC / RFID-Tags
238 0 1 -
-
-
