|
KiCADKicad
|
ESP32 S3 Relay control
This project aims to control up to 4 relays remotely either using WIFI or Bluetooth. The SOC ESP32 S3 is used as the main core of the project, it provides wifi and Bluetooth to the project, as well as great processing power thanks to the two cores it has.
This project can be powered with a 5-volt DC both through the USB connector as well as through the external power connector. The relays also work at 5 volts DC, which means no extra power supply is required to run them.
Each relay has an LED to indicate if the relay is activated or deactivated. The board also has an RGB LED which is controlled with a single GPIO of the microcontroller because this RGB is directional.
As inputs, there are 4 user buttons, which can be used to control the flow of the program. It also has a 16-pin header which has 16 GPIOs for external use, among which there are I2C, SPI, UART, USB, and ADC connections, among other peripherals.
There is also a 6-pin header with 5V, 3.3V, and GND outputs for external use.
Domostration: https://youtube.com/shorts/JGW6t4wU7uA
ESP32 S3 Relay control
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(8)
- Likes(18)
- Fatria Gumelar Jan 03,2024
- Francisco Hernandez Dec 29,2023
- Eric Estrada Dec 06,2023
- Ellen Lemos Dec 06,2023
- Ivan Verges Dec 06,2023
- Yeribi Medina Dec 06,2023
- Rosanna Mejia Dec 06,2023
- Ariel Henriquez Nov 28,2023
- Manny Peralta Nov 28,2023
- Emilenny Gonzales Nov 28,2023
- Emely Olivares Nov 28,2023
- Juan Urbano Nov 27,2023
- Alex Shaw Nov 27,2023
- Engineer Nov 25,2023
- Engineer Sep 05,2023
- Wandy Amaury Sep 04,2023
- LuckSkyGyver Sep 04,2023
- Alex Spataru Aug 23,2023
- 7 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
-
9design
-
9usability
-
9creativity
-
9content
-
8design
-
8usability
-
9creativity
-
9content
-
10design
-
10usability
-
10creativity
-
10content
-
10design
-
10usability
-
10creativity
-
10content
-
10design
-
10usability
-
10creativity
-
10content
-
10design
-
10usability
-
10creativity
-
10content
-
10design
-
10usability
-
10creativity
-
10content
More by Wandy Amaury
- RF Control training board for students based on ESP32 C3 RF control training module for students.This project is a training module that has the ESP32 C3 SOC ...
- christmas snowflake Christmas snowflake with a steady light. This circuit consists of a 3v DC CR2032 battery, a switch, ...
- Halloween pumpkin PCB PCB in the shape of a Halloween pumpkin. This PCB project is for the Halloween festivities, which is...
- Buck Switching Regulator 7V to 40V DC to 5V DC fixed using the LM2575-5 regulator This is a simple but very useful project when working with electronic devices that must be powered w...
- Servo motor tester using a 555 IC This project is a basic servo motor tester based on the IC 555 as the signal modulator. The project ...
- 2WD RF Car training board for students based on ESP32 C3 2WD RF development module based on the ESP32 C3 SOCThis project is aimed at students who are startin...
- ESP32 C3 Wireless development board for students This project is an IOT training module for students who are starting in the world of electronics and...
- San Valentine Cupido PCB using a 4017 IC This project is a PCB in the form of Cupido for San Valentine's Day. The project has 10 simple LEDs ...
- San Valentine PCB Heart This project is a PCB in the form of a heart of San Valentine´s Day which has 6 cycling RGB LEDs to ...
- Traffic Light using NE555 and 4017B This is a simple Traffic Light project for beginner students in electronic engineering. This Project...
- Led chaser using a 555 and 4017B ICs This is a simple project for students who are interested in the magic world of electronics, this is ...
- Christmas tree PCB using a NE555 IC Christmas PCN project with which students can easily create this circuit with an NE555 oscillator.As...
- ESP32 S3 students Wireless training board This project is a training board based on the ESP32 S3 microcontroller, whose main objective is to p...
- ESP32 Zodiac Clock RGB training board ESP32 Zodiac ClockThis project is ideal for students who are starting with microcontrollers and espe...
- Breadboard power supply with variable voltage output This project is ideal for breadboard power supply so that different output voltages can be configure...
- LM317_regulator-V1 This is a simple project but also very important when powering an electronic circuit. This LM317-bas...
- ESP32 S3 Relay control This project aims to control up to 4 relays remotely either using WIFI or Bluetooth. The SOC ESP32 S...
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
497 0 0 -
RF Control training board for students based on ESP32 C3
667 0 2 -
Aquarius+ Computer, Standard PCB
883 0 4 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
603 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
527 0 1 -
Nintendo Famicom HVC-001 Controller Shells
623 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
585 0 4 -
COMMODORE 128 15KHz DISPLAY ADAPTER (C128 80 COLUMN ADAPTER)
793 1 6 -