Popular: Arduino Automation Commodore Iot Raspberry pi
Projects 84
Questions 7
Feedback 96
Blog 3
Sponsorships 3
BoomBay 525 Case - Speakers in your 5.25" Drive Bay
b5s4 Mar 15,2026
This is the mounting case for the BoomBay 525. It mounts in a spare 5.25" drive bay of your computer and provides a set of stero audio speakers with volume control and headphone output. It's primarily designed for retro-computers, but could be used in a modern computer.If you print the screw nuts, you will need 4 of themBoombay 525 PCBhttps://www.pcbway.com/project/shareproject/BoomBay_525_Speakers_in_your_5_25_Drive_Bay_84e0584a.html
Commodore Amiga PC
196
0
0
BoomBay 525 - Speakers in your 5.25" Drive Bay
b5s4 Mar 15,2026
This is a tested and working projectThis project provides you with a set of small stereo speakers which can be directly mounted in a spare 5.25" drive bay of a computer. It is primarily intended for retro computer systems, but it could be used with modern systems if you were inclined to. Full instructions on assembly and case are available in the GitHub.FeauresStereo speakersVolume ControlPower LEDFront headphone jackBOM (THT)2 x 1nF Mylar/Film Capacitors2 x 150nF Mylar/Film Capac...
audio speakers amiga
204
1
0
BassX 30A Relay Speaker Protection Circuit Board for Power Amplifiers
X Mar 11,2026
BassX Speaker Protection PCB – Active, Protect, Clip & Signal IndicatorThe BassX Speaker Protection PCB is designed to protect valuable speakers and amplifiers from power-on surges, DC faults, and clipping conditions. This compact and reliable protection board automatically delays speaker connection during amplifier startup and immediately disconnects the speaker if abnormal conditions are detected.The circuit uses a high-current relay and transistor-based detection to ensure stable and fast...
368
2
0
Speaker soft start (dual) - protetor antipop/thumps para falantes
Toledo Mar 06,2026
Projeto originalmente publicado em https://diypowered.llucastoledo.com.br/2023/12/protetor-antipop-para-alto-falantes.htmlProjeto consolidado e maduro, publicado aqui no site há algum tempo, foi aplicado em vários projetos diyPowered e também em equipamentos de terceiros como melhoria, o speaker soft start protege as caixas acústicas contra pops e thumps originados do acionamento do amplificador. Características e funcionamentoO funcionamento é muito simples: ao ser acionado pela fonte auxi...
Audio DIY Stereo
318
0
0
3D printed planar speaker
ELECTRONOOBS Feb 10,2026
How to make speakers using planaer PCBs.
658
0
1
tinyclock002 -- 5x5cm CH32V002 devboard with LEDMUX, RTC, piezo and speaker, easy expansions.
Feb 03,2026
A simple board to get started with the CH32V002, with easy access to I2C and UART expansion, as well as onboard RTC (can fit either a supercap or a CR2032 holder, the DS1302Z+ can be set to trickle charge the supercap, allowing lesser part count), 12 LEDs multiplexed and arranged in a circle to display nice pattern effects (see video in repository, the matrix is controlled with a 74HC595 shift register, dropping pin count requirements from the CH32V002), headers to add a push button and linear p...
Development board LED Display
367
0
0
The Engineering Tablet
er Jan 23,2026
Many devices now-a-days that are used for engineering purposes are already pre-programmed and have no flexibility. They use proprietary software and hardware for different purposes. If you needed an oscilloscope for PCIe, that analyzer is designed to do that and nothing else. The hardware inside and the software that is flashed onto it are not usually public knowledge. Certainly, with microcontrollers and FPGAs, the user can program them to do whatever the engineer wants, but those are not indus...
8th Design Contest-AIoT Project Tablet IOT
549
0
1
Fully 3D printed Speaker
Printing Jan 05,2026
This is the basic components of a 3D printed speaker; you need to add magnets and copper wire, Along with getting the plates cut from a local or online laser cutterThe cone, cap spider and surround have been vacuum formed using included molds, however I've included a STEP file that can be used to generate any needed .stl files from, the output from the speaker is unknown using those parts straight from a printer though. Use at your own risk. The Surround should be printed in TPU or this speaker ...
8th Design Contest-Mechanical Project Speaker AUdio
1407
0
4
Multiway Speaker Crossover Board
Harrison Dec 08,2025
multiway crossover with good phase can use two sided PCB. There are two other alternative designs in other files for assembly
DIY Audio Stereo
353
1
1
AEL-2011 Power Supply Module
Electronics Lab Nov 27,2025
NOTE: THIS INVOLVES MAINS WIRING AND MAINS POTENTIAL. IF YOU ARE NOT CONFIDENT IN HANDLING MAINS WIRING, DO NOT ATTEMPT THIS PROJECT.IntroductionThis power supply module is intended for use with the AEL-2011 power amplifier, described here, but can be used as the basis for any amplifier power supply. This features a DC detection circuit and muting function to prevent speakers from being destroyed if the amplifier connected to them has a DC fault condition.ConstructionDo not install Q1 or the hea...
Audio Amplifier DIY
2495
0
2
1 2 3 4 5 6 7 8 9
Popular Creator
Juan A. Vargas Diaz
Excellent Engineer
Project: 4 Followers: 46
Prem Kumar
Excellent Engineer
Project: 28 Followers: 1391
Debashis Das
Excellent Engineer
Project: 5 Followers: 299
Leo
Excellent Engineer
Project: 2 Followers: 7
Murgia
Excellent Engineer
Project: 11 Followers: 57
Popular Project
Bruce RF Reaper PCB
Explore!https://bruce.computer MCU ESP32 S3 N16R8BATTERY 1000MAH6 WAY BUTTONAW9523 IO EXPANDERNRFCC1101 433MHZNFC ST25R3916VIBROBUZZERIR TX RXIBUTTONSDCARDLEDGPSFLIPPER ZERO HEADER COMPATIBL...
LTS Respooler Control Board
The LTS Respooler is a compact and slightly over-engineered filament Respooler optimized for Bambu Lab spools. It integrates a filament runout sensor and wireless app-connectivity for ease of use.!! I...
Self-Balancing Robot PCB
This is the PCB for the self-balancing robot seen in this video: https://youtu.be/K1lzzVGCzAQModel can be fully 3D printed at this link (zero supports required): https://www.printables.com/model/15335...
The Sesame Robot Project
What is Sesame?Sesame is a 3D-printable quadruped robot powered by an ESP32. It runs on 8 MG90S metal-gear servos (two per leg) and features a 128x64 OLED display for a face. It walks, dances, waves, ...
World's Smallest 1S Battery Charger
This is a very small 1S lithium battery charger board designed for projects where space is extremely limited. It charges single-cell Li-ion or Li-Po batteries (3.7V nominal) using a USB Type-C input. ...
View More
Hot Project Tags
Space Exploratio Virtual reality Microcontroller DIY Synthesizer Weather Station Synthesizer Antenna TVC