Power Distribution Board (PDB) for Drones
This is a basic Power Distribution Board for Drones (Quadcopters)
You can use it as a bare PCB to connect via XT60 socket to the battery. Use big pads to connect ESCs. There are pads for 8 connections.
If you solder other parts you can get 5V and a LED light if power is connected.
Parts Needed:
XT60 Connector (Male)
10uF SMD Capacitor (1206) x2
NCP1117ST50T3G SOT223
180ohm Resistor 0603
LED 0805
Have Fun
*** Always disconnect propellers before you give power to your drone ***
Note: Holes are 30.5x30.5 standard
Power Distribution Board (PDB) for Drones
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(4)
More by Secco41
-
C64 Pico Cart
Thanks to cknave for the project, Not tested and I will try and share comments about this project.
-
Guitar Overdrive V1
A DIY Guitar Overdrive Pedal PCBThis project is not tested yet, I will test it in a short while, mea...
-
3PDT Footswitch Connection Board for DIY Guitar Pedals
A simple PCB to connect 3PDT footswitch to your projects. Especially home made DIY guitar pedals.
-
ESC for 2-4S batteries, Quadcopters, Cars, Planes, Ships Etc
I built an ESC to try to work for my Quadcopter. I used high power MOSFETs. (80 amps)The PCB is big ...
-
Power Distribution Board (PDB) for Drones
This is a basic Power Distribution Board for Drones (Quadcopters)You can use it as a bare PCB to con...
-
MAX7219 Driver Board for 7 Segment Display
This is a tested and working project.Use this board to easily integrate 7 segment displays in your p...
-
SwinSID Micro
SwinSID is a microcontroller based clone of the SID, the audio chip used in nearly all 8-bit Commodo...
-
KungFuFlash Cartridge for Commodore 64
This is a project by Kim JorgensenDetails can be found on his github page: https://github.com/KimJor...
-
6502 (W65C02S) to Atari SALLY adapter Board
This project has been developped by TheByteAttic, Thanks for this awesome project,Check his youtube ...
-
Playstation 2 Dualshock to DB9 Adapter Board (Double Connector)
This project is tested and runs okay :)This version is only for C64This board is an extended version...
-
DRAM Test Shield for Arduino Uno and Nano
This project is tested and works okay!To use it with Arduino Uno, solder male pin headers on the bot...
-
Dennis RGB to HDMI Adapter for Amiga 500 with Raspberry Pi Zero
A Dennis chip adapter to give your Amiga HDMI output. Check project documentation for details and BO...
-
GVP-Compatible 64-Pin 4MB SIMM
GVP-Compatible 64-Pin 4MB SIMM PCB for GVP Accelerator Cards,Made by: Tube TimePlease check the site...
-
Amiga 500 Kickstart EPROM Adapter for Rev 5 Boards
You can use your burned EPROM chips (27C400 and 27800) with your Amiga 500 Rev5 boards.Bill of Mater...
-
Playstation PS2 Dualshock to DB9 (DSUB 9) Adapter for Commodore, Amiga and Atari Computers
Use Arduino pro mini to connect your Playstation 2 Dualshock to your retro computers. Like Commodore...
-
-
-
-
Tester for Touch Screen Digitizer without using microcontroller
232 2 2 -
Audio reactive glow LED wristband/bracelet with NFC / RFID-Tags
238 0 1 -
-
-
