|
EagleAutodesk
|
Eurorack Moog CP3 Clone Mixer
Moog CP3 is an classic synthesizer circuit, it adds subtle, warm "minimoog" distortion to your Eurorack modular audio synthesizer.
Some think this mixer design gives vintage moog instruments their classic "fat" sound.
Presented here is a 3 PCB design for Eurorack skiff (+/- 12V power, 3.5mm jacks; less then 30mm deep).
You will need 3 boards to build the entire design,a front panel, a board for pots and jacks, and the mixer PCB.
This community project page provides the gerber for the main board, but again there are 3 boards for this design.
Get all 3 gerbers (front panel, mixer, mixer pots board, all in ZIP format) as well as PDF of layout, schematics, etc., from the cslammy Github repository: https://github.com/cslammy/CP3 or in a zip file in this community project posting.
You can read more about the design and build at this blog post: https://audiodiwhy.blogspot.com/2022/09/cloning-moog-cp3-mixer.html
Eurorack Moog CP3 Clone Mixer
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(7)
More by AudioDIWHY
-
BNC to Banana x3 adapter board
I needed an easy way to adapt BNC to banana. There are plenty of M < > F adapters out there, b...
-
LFO Mini: CA3080 based LFO
I needed a small PCB for upcoming projects where a Low Frequency Oscillator will be required. I also...
-
LFO2 From "Electronics For Musicians"
Analog LFO with variable frequency and lots of modulation options based on an EFM ("Electronics for ...
-
JTAG to SWD Converter
Simple JTAG to SWD adapter.My use case is Segger J-LINK EDU MINI to Raspberry Pi Pico but this board...
-
Rotary Encoder Experimenter's Dev Board
UPDATE: new revision 9-29-24 posted. Lower parts count, more reliable software debouncing for the en...
-
Bench 4x2 Bluetooth Mixer
Simple 14HP Eurorack 4x2 synth mixer.outputs are 2x 100mil terminal posts on rear of PCB.You will ne...
-
Anything to Clock--LM311 based
I needed a simple circuit to condition incoming signals so a MCU could read them as clock:--rectify ...
-
Vactrol Based Audio Envelope Follower
An audio envelope follower based on a 5C3 Vactrol. Useful for auto-wah (send its output to a bandpas...
-
Warm Floater Eurorack Power Extender
I ran out of physical connections on my Eurorack Power supply. This PCB supplies 1 input and 3 outpu...
-
"KiCADSR" Euro Envelope Generator
This is my first project using KiCAD for EDA instead of Autodesk Eagle.I wanted to see if I had the ...
-
Low Noise Preamp based on Arp 2600 Synthesizer
The Arp 2600 synthesizer has a preamp that takes an unbalanced signal and amplifies it 10x, 100x, an...
-
Arp 2600 clone--inverter-mixer
The ARP2600 is a legendary, classic semi-modular analog synthesizer. Its voltage processor circuitr...
-
SEEED XAIO RP2040 ADC and Buffer Board
The SEEED XAIO RP2040 is a fantastic little dev board, featuring the RP2040 MCU.I needed a buffered ...
-
Dual LFO daughterboard
I needed a small Dual LFO (2 independent LFO's on a single PCB) for future projects. This PCB is bas...
-
CV Generator
A 3x CV Generator for synthesizers. Outputs are -10 to +10V DC with about 20mA source/sink current. ...
-
BNC to 3.5mm x3 adapter board
I needed some BNC to 3.5mm conversion and didn't want to use unreliable and fragile adapters or cust...
-
Voltage Controlled Stereo Panner
This is a modular synthesizer stereo panner for audio or control voltages.This is a modular project ...
-
Dual Concentric Pots to 4x JST XH 3 pin males
Needed an easy way to add dual concentric pots to my project. The PCB featured here accommodates 2 c...
-
-
-
-
Tester for Touch Screen Digitizer without using microcontroller
229 2 2 -
Audio reactive glow LED wristband/bracelet with NFC / RFID-Tags
235 0 1 -
-
-
