COMMODORE AMIGA SDBOX ( jbilander / sdbox )
GNU General Public License v3.0
SDBOX (A parallel to sd-card project for the Amiga)
parallel2SD on amiga 500
https://www.youtube.com/watch?v=cdjNlg5xI-g
Amiga500 WB 1.3 whdload via JST , sdbox (microsd parallel Port hdd)
https://www.youtube.com/watch?v=VQdrOjCI9As
MIGs Yesterchips - Folge #097 SD-Box
https://www.youtube.com/watch?v=AxWvHaGmrws
For more information: https://github.com/jbilander/sdbox
BOM, now verified!
Please note, you don't need to populate C1 if you're not going to use the barrel jack. R5 is only needed if U3 is populated.
***
PART | Value | Description
----- | ----- | -------
U2 | | Micro SD-Card Adapter (with onboard bidirectional level shifter)
U2 |Pin strip| 1 Pcs 2.54mm Single Row Male Pin Header Strip For mounting and connecting Micro SD-Card Adapter directly into base PCB. Cut out one with 6 pins and two with single pins. The current angled pins on module will be desoldered and removed.
U3 |PVG612S| Solid State Relay, 6-SMD (0,300", 7,62mm) Automatic power down with the Amiga (optional)
J1 |DB25 | DB25 Male MountingHoles
J2 |5.5x2.1 mm | Barrel Jack Power Connector, center positive (optional)
C1 |100uF-220uF| 1210 ceramic decoupling capacitor for VIN, 16 VDC or at least above you voltage input 7-12V. Not needed if powering via USB.
R1 |4.7k Ohm| 1206 smd resistor (should give around 0.9mA when CS/SEL is high)
R2 |4.7k Ohm| 1206 smd resistor
R3 |120 Ohm| 1206 smd resistor (should give around 2.14V, 24 mA over D1)
R4 |120 Ohm| 1206 smd resistor (should give around 2.17V, 24 mA over D2)
R5 |330 Ohm| 1206 smd resistor (should give around 1.2V and 10 mA control current with the Amiga 47 Ohm in series from pin 14) Not needed if U3 not populated
D1 |LED 3mm| SD Activity LED, Diffused Orange / Amber, pitch 2.54 mm, 1.8V-2.3V, 20-30 mA, 605-610nm
D2 |LED 3mm| Power LED, Green Diffused T-1, pitch 2.54 mm, 25 mcd, 565 nm, 2.2 V, 25 mA
Q1 |BC847BW| Small Signal Transistor, NPN polarity, SOT-323
Q2 |BC847BW| Small Signal Transistor, NPN polarity, SOT-323
JP1 |Solder jumper| Enable this to reset Nano in conjunction with Ctrl-Amiga-Amiga
JP2 |Solder jumper| Enable this to use barrel jack connector without U3 chip
Note
I take no responsibiltiy for any damage to any equipment that results from the use of this board.
USE AT YOUR OWN RISK!
COMMODORE AMIGA SDBOX ( jbilander / sdbox )
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(1)
- Likes(23)
- Engineer Oct 29,2024
- Daniel Mackey Oct 02,2024
- Tony RetroManiak Aug 24,2024
- ugur tezer Aug 19,2024
- MATTHEW WATERFALL Feb 28,2024
- Kai Lais Feb 26,2024
- Engineer Nov 18,2023
- Oliver Renz (K.Zonias) Nov 18,2023
- Darren Bassett Jun 23,2023
- Giovanni giobbi May 30,2023
- Mark Peter Vargha Sep 18,2022
- Engineer Aug 30,2022
- IVCP Aug 23,2022
- Jorge Tavares Jul 26,2022
- Simon Barbara Jun 27,2022
- Mert Uckan Apr 02,2022
- Mariano Apicella Dec 01,2021
- Steve Nov 28,2021
- Emre Demirkilic Nov 13,2021
- Fernando Bugallo Oct 10,2021
- raparici Oct 07,2021
- nortos Sep 24,2021
- Oleksandr Siryj Sep 16,2021
- 1 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
-
10design
-
10usability
-
10creativity
-
10content
More by Alex Soyovan
- ATARI FUJINET 1.7.1 Note from PCBWay: There are some problems in the BOM on the project page that cannot be resolved. If...
- Commodore & Atari like joystick adapter to USB by mistepien mistepien/joy2usbhttps://github.com/mistepien/joy2usbGerber; joy2usb_7.0.zipAtari-like joystick adap...
- Atari 8 Bit Pico Cart - A8PicoCart by Robin Edwards Atari 8 Bit Pico Cart - A8PicoCart by Robin EdwardsA8PicoCart (UnoCart on a Raspberry Pi Pico clone)...
- XGecu T48 Programmer Adapter DIP42/PLCC44 for 27C800/160/322 27V800/160/322 MX27C8100/1610 XGecu Programmer Adapter DIP42/PLCC44 for 27C800/160/322 27V800/160/322 MX27C8100/1610Only for T48 P...
- FDDEMU1.1 PROJECT FDDEMU1.1 PROJECTGNU General Public License v3.0PermissionsCommercial useModificationDistributionPat...
- ATARI 2600 8K/16K/32K Bankswitch Cartridge Creative Commons Attribution 4.0 International license.http://www.grandideastudio.com/pixels-past/C...
- HID2AMI HID MOUSE AND GAMEPAD to AMIGA ADAPTOR (REV 1.1 board) Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International Public Licensehttps://github...
- PS/2 SERIAL MOUSE ADAPTER / necroware (For converting PS/2 mouse to serial mouse) GNU General Public License v3.0,For more information: https://github.com/necroware/ps2-serial-mouse-...
- COMMODORE AMIGA SDBOX ( jbilander / sdbox ) GNU General Public License v3.0SDBOX (A parallel to sd-card project for the Amiga) parallel2SD on am...
- AMIGA 600 KEYBOARD MEMBRANE PCB 2021-09-29 (arananet) Creative Commons Attribution Share Alike 4.0 InternationalGerber: tecladoa600dual_2021-09-29.zipFor ...
- AMIGA 600 KEYBOARD MEMBRANE PCB (arananet) Creative Commons Attribution Share Alike 4.0 InternationalFor more information:https://github.com/ar...
- AMIGA 600 KEYBOARD PCB MEMBRANE HEADER (arananet) Creative Commons Attribution Share Alike 4.0 InternationalOne of the layer in GERBER file is blank, ...
- C64-WiFi-Modem-User-Port Rev.2 by svenpetersen1965 GNU General Public License v3.0https://github.com/svenpetersen1965/C64-WiFi-Modem-User-Porthttps://g...
- PISTORM for COMMODORE AMIGA (A 68000 CPU replacement) captain-amygdala/pistorm is licensed under theMIT LicensePermissions Commercial use Modification Dis...
- Nano SwinSID (SID replacement for Commodore 64) Nano SwinSID for Commodore(SID replacement for Commodore 64)For more information http://www.tolaem...
- EASYFLASH CARTRIDGE3 PCB V1.3 EASYFLASH CARTRIDGE3 PCB V1.3https://skoe.de/easyflash/https://bitbucket.org/skoe/easyflash/src/mast...
- KungFuFlash Cartridge rev.2 KimJorgensen/KungFuFlash is licensed under thezlib LicensePermissions Commercial use Modification Di...
- AMIGA 500 RGB TO HDMI V2 AMIGA 500 RGB TO HDMI V2https://github.com/hoglet67/RGBtoHDMIhttps://github.com/hoglet67/RGBtoHDMI/w...
-
High Precision Thermal Imager + Infrared Thermometer | OpenTemp
166 0 4 -
Sony PlayStation Multi Output Frequency Oscillator (MOFO) v1
69 0 1 -
-
XRC PRO: Open-Source RC Transmitter and Receiver System
78 0 2 -
-