4 input Mono Eurorack Audio Mixer
I need a few small (but not too small!) Eurorack 4 x 1 DC coupled mixers for my rack.
Many simple commercially available Eurorack synth mixers are extremely small, making it hard to turn the gain up or down, especially with a lot of patch cords in the way.
I designed this module to use dual contentric pots: reasonably large knobs but, in the Eurorack tradition, occupying a relatively small space.
The design utilizes 3 PCB's: main board, jacks, and front panel.
If you fabricate the front panel for the project I'd suggest using black soldermask with white silks, and choose the "leave the build number off" option (costs an extra $1.50).
For alacrity: all parts except for an optional 1206 resistor on the jacks board are through-hole--overall this is a really easy build, it took me about a half hour to build.
For details please see the blog post:
https://audiodiwhy.blogspot.com/2024/09/4-x-1-mono-mixer-confidence-builder.html
4 input Mono Eurorack Audio Mixer
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(1)
More by AudioDIWHY
-
BNC to Banana x3 adapter board
I needed an easy way to adapt BNC to banana. There are plenty of M < > F adapters out there, b...
-
LFO Mini: CA3080 based LFO
I needed a small PCB for upcoming projects where a Low Frequency Oscillator will be required. I also...
-
LFO2 From "Electronics For Musicians"
Analog LFO with variable frequency and lots of modulation options based on an EFM ("Electronics for ...
-
JTAG to SWD Converter
Simple JTAG to SWD adapter.My use case is Segger J-LINK EDU MINI to Raspberry Pi Pico but this board...
-
Rotary Encoder Experimenter's Dev Board
UPDATE: new revision 9-29-24 posted. Lower parts count, more reliable software debouncing for the en...
-
Bench 4x2 Bluetooth Mixer
Simple 14HP Eurorack 4x2 synth mixer.outputs are 2x 100mil terminal posts on rear of PCB.You will ne...
-
Anything to Clock--LM311 based
I needed a simple circuit to condition incoming signals so a MCU could read them as clock:--rectify ...
-
Vactrol Based Audio Envelope Follower
An audio envelope follower based on a 5C3 Vactrol. Useful for auto-wah (send its output to a bandpas...
-
Warm Floater Eurorack Power Extender
I ran out of physical connections on my Eurorack Power supply. This PCB supplies 1 input and 3 outpu...
-
"KiCADSR" Euro Envelope Generator
This is my first project using KiCAD for EDA instead of Autodesk Eagle.I wanted to see if I had the ...
-
Low Noise Preamp based on Arp 2600 Synthesizer
The Arp 2600 synthesizer has a preamp that takes an unbalanced signal and amplifies it 10x, 100x, an...
-
Arp 2600 clone--inverter-mixer
The ARP2600 is a legendary, classic semi-modular analog synthesizer. Its voltage processor circuitr...
-
SEEED XAIO RP2040 ADC and Buffer Board
The SEEED XAIO RP2040 is a fantastic little dev board, featuring the RP2040 MCU.I needed a buffered ...
-
Dual LFO daughterboard
I needed a small Dual LFO (2 independent LFO's on a single PCB) for future projects. This PCB is bas...
-
CV Generator
A 3x CV Generator for synthesizers. Outputs are -10 to +10V DC with about 20mA source/sink current. ...
-
BNC to 3.5mm x3 adapter board
I needed some BNC to 3.5mm conversion and didn't want to use unreliable and fragile adapters or cust...
-
Voltage Controlled Stereo Panner
This is a modular synthesizer stereo panner for audio or control voltages.This is a modular project ...
-
Dual Concentric Pots to 4x JST XH 3 pin males
Needed an easy way to add dual concentric pots to my project. The PCB featured here accommodates 2 c...
-
-
-
-
Tester for Touch Screen Digitizer without using microcontroller
229 2 2 -
Audio reactive glow LED wristband/bracelet with NFC / RFID-Tags
235 0 1 -
-
-
