PCBWay
Dec 03,2013
648
IEK: PCB production growth slowing to PCB industry market new bureau
Engineering institute IEK components researcher Jiang Baifeng pointed out that Taiwan PCB industry output value estimates for this year only increased 1.5%, reflects the excessive pour heavy structure...
PCBWay
Dec 03,2013
728
PCB design still have to look for the six key points
Many engineers feel some layout work is more important, schematic diagram is convenient to generate netlist PCB do check in. In fact, in the subsequent circuit schematic diagram in the process of debu...
PCBWay
Dec 03,2013
716
How to make your PCB design more good
Many people think of PCB layout work is boring, a day on the board article tens of thousands of lines, all kinds of packaging, pull up. But the designers to make trade-offs between the rules of variou...
PCBWay
Dec 03,2013
745
PCB copy board for environmental protection during the break of large equipment monopoly
As is known to all, carry through the smartphone camera or sensors, even there is no real contact with smart phones, it can detect the user's gesture, and provides some relevant, complex or simple hum...
PCBWay
Dec 03,2013
885
PCB copy board, chip decryption information security defense
In the recently held on the third plenary session of the central puts forward to set up the national security council, perfecting the system of national security and national security strategy, to ens...
PCBWay
Dec 03,2013
727
Trade community is a core power of modern PCB design, but its role has not been fully revealed
PCB design software vendors CadSoft Computer (e complex written following company) have made a set of global PCB designer survey data to celebrate its 25th anniversary. Since it was founded in 1988, C...
PCBWay
Dec 03,2013
1266
What is PCB industry
PCB (printed circuit board) is one of the most active industry in modern electronic components industry, the industry growth rate is generally higher than the electronic components industry is about 3...
PCBWay
Dec 03,2013
2610
Light Alarm Circuit with LDR
This musical light alarm circuit is very simple, uses only 7 components, a LDR and a 3.6 V battery or 3 x 1.2 volts rechargeable batteries. The well-known UM66 is used as the sound generator and will ...
PCBWay
Dec 03,2013
3017
4011 IC Circuit
The HEF4011B is a quad 2-input NAND gate. The outputs are fully buffered for the highest noise immunity and pattern insensitivity to output impedance. It operates over a recommended VDD power supply r...
PCBWay
Dec 03,2013
3106
IC CA3130 Circuit
CA3130A and CA3130 are op amps that combine the advantage of both CMOS and bipolar transistors. Gate-protected P-Channel MOSFET (PMOS) transistors are used in the input circuit to provide very-high-in...
PCBWay
Dec 03,2013
968
PCB printed circuit board factory at the end of the off-season camp seized a success
Sony (Sony) PS4, Microsoft XboxOne on sale come out in succession, xin xing (3037), said han yu bo, south electricity from printed circuit board factory, to the end of season sales have injections, so...
PCBWay
Dec 03,2013
821
Similar PCB copy board compensate for generating set strategic innovation
With the development of science and technology, high load can industry, manufacturing power consumption growth continuously, to our country the technical requirements of large hydroelectric generating...
PCBWay
Dec 02,2013
812
The Basics of PCB Manufacture
printed circuit boards perform two functions. They provide mechanical support for electronic devices and connect all the devices through conductive traces. Today, they are nearly universal in electron...
PCBWay
Dec 02,2013
948
Complex PCB Design
printed circuit boards or PCBs are the foundation of modern electronics. They do more than simply provide electrical connections between components. Some incorporate an internal ground plane for signa...
PCBWay
Dec 02,2013
754
How Printed Circuit Boards Became the Best Way to Connect Electrical Components
Up to the 1960s electronic parts were wired up point to point by hand soldering wires and components to tags and tag boards. This was extremely laborious and expensive. Quality was also poor because i...
PCBWay
Dec 02,2013
3226
How to Design an Enclosure for a Printed Circuit Board Assembly (PCBA)
The leading electronic component suppliers hold stocks of literally thousands of various types of enclosures so there is little point in paying for the tooling costs necessary to manufacture your own ...
PCBWay
Dec 02,2013
1671
PCB Autorouter
Pcb includes an autorouter which can greatly speed up the layout of a circuit board. The autorouter is a rectangle-expansion type of autorouter based on “A Method for Gridless Routing of Printed Circu...
PCBWay
Dec 02,2013
1745
PCB Polygons
Sometimes it's useful to fill large areas with solid copper. The way to do this is with polygons. Polygons can be created in either the polygon mode or the rectangle mode. In the polygon mode, you'll ...
PCBWay
Dec 02,2013
1175
PCB lines
Lines are used to draw tracks on the pc board. When in the line mode, each Btn1 press establishes one end of a line. Once the second point is defined, the line is drawn and a new line started where th...
PCBWay
Dec 02,2013
1516
PCB layers
Every layout consists of several layers that can be used independently or treated as a group. Layer groups can be used to logically separate (and color-code) different traces (e.g. power and signal); ...
| Ranking | Name | Answers |
|---|---|---|
| 1 | PCBWay Team | 4 |
| 2 | KhronoSound Audio | 1 |
