PB1 - Prototyping Board with Ground Plane and Power Supplies
This board is for prototyping circuits using wire wrap. It has a good ground plane and power supplies for +12V, -12V, and +5V.
There are pads for two trimpots (3362) and a pushbutton switch. For the trimpots I use pins from a wirewrap socket so I can wirewrap to them and change the trimpots.
For other pins that I want to wirewrap to I use either a T49 pin from Vector Electronics or, much cheaper, the pins from headers. On eBay the headers are called 2.54mm Male PCB Single Row Straight Header Strip Connector Arduino. The pins are smaller than standard wirewrap pins but they are square and seem to wrap ok.
The ICL7660CPA is only good for 10-15mA. If you need more than that use an LT1054 and change R2 and R3 to 10 Ohms (or so). The LT1054 is good for 100mA.
If you are not already a Maker (and you want to be one) see my tutorial on Making Things at www.jmargolin.com/making/jm_making.htm
Now go out and do something splendid.
JM
PB1 - Prototyping Board with Ground Plane and Power Supplies
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(0)
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Jed Margolin
- MyTX4 To Replace The La Crosse TX4U My TX4 Wireless Sensor Transmitter replaces the La Crosse TX4U wireless sensor which is no longer ma...
- Audio Tone Burst Generator The Audio Tone Burst Generator produces a periodic burst of tone at a User-selected audio frequency ...
- Woof Meter The Woof Meter is for testing subwoofer speakers to measure their Thiele-Small (TS) parameters. Thes...
- Precision Low Frequency Signal Generator The Precision Low Frequency Signal Generator produces a User-selected signal from 10Hz to 90Hz with ...
- GPS Clock and Armageddon Alarm A GPS Module using the U-blox NEO6MV2 is used to receive the GPS timing signals to show the exact ti...
- PB1 - Prototyping Board with Ground Plane and Power Supplies This board is for prototyping circuits using wire wrap. It has a good ground plane and power supplie...
- Flame Switch This board simulates the electrical characteristic of a flame for troubleshooting residential gas fu...
- PB2 - Prototyping Board for MSP430G2xxx This board is for prototyping circuits with the Texas Instruments MSP430G2xxx microcontroller. It ca...
- GP1 - Board for demonstrating how to use an MSP430G2xxx This board is for demonstrating how to use the Texas Instruments MSP430G2xxx microcontroller. The bo...
- VGA Adapter for Atari Hard Drivin’/Race Drivin’ Cockpit This VGA Adapter for Atari Hard Drivin’/Race Drivin’ Cockpit also provides for delaying horizontal a...
- Phone Selector/Adapter 2-line to 1-line This converts an RJ11 line with two phone pairs on it to two single line RJ11 jacks. It provides two...
- Triangle Wave Generator With Adjustable Symmetry This is a simple circuit using only one IC, a TL084 quad opamp. The integrator integrates the output...
- Voltage Controlled Audio Oscillator with LM13700s This is a voltage controlled audio oscillator using two LM13700s. At 1 KHz ARTA software (http://www...
- Oscillator - Xtal or RC This is an oscillator that can be stuffed to be either a crystal oscillator (with a 74HC04) or an RC...
- Sine Wave Generator Using a Johnson Counter This is a 1KHz audio oscillator using a Johnson Counter. ARTA software (http://www.artalabs.hr/) rep...
- VGA Adapter For Tektronix TDS 360 Oscilloscope The Tektronix TDS 360 is a two-channel digital oscilloscope from the middle 1990s. The sampling rate...
- Atari BattleZone Engine Sound Generator Atari’s BattleZone game is considered the first real 3D video game. I did the 3D graphics algorithms...
- Der DeZapper Der DeZapper entl?dt die statische Ladung, die Sie vom gehen auf Teppich bekommen. Dies verhindert, ...
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
463 0 0 -
RF Control training board for students based on ESP32 C3
614 0 2 -
Aquarius+ Computer, Standard PCB
821 0 4 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
575 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
502 0 1 -
Nintendo Famicom HVC-001 Controller Shells
597 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
553 0 4 -
COMMODORE 128 15KHz DISPLAY ADAPTER (C128 80 COLUMN ADAPTER)
752 1 5 -