Simone
ITALY • + Follow
Edit Project
Description
Isolated USB to UART Converter with Arduino pro mini connector
This project is available on KickStarter!
https://www.kickstarter.com/projects/1351830006/isolated-usb-to-uart-converter-for-arduino-pro-min
Description
It's a USB to UART converter with a digital isolator at the UART side.
It has a micro USB for connecting to the PC and a 6 pin header with the same pin-out of the Arduino Pro mini board.
The chip FT231XQ is used as interface between the USB and the UART protocol, while the Si8642 is used for isolate the board from the PC.
This converter is very useful if you are working on some projects and worrying about short circuit with the main power supply. Because the isolator isolates the two sides therefore there is no electrically connection.
Advantages
- You don't burn your PC in case of some accidents between your project and the main power supply. Check our test!
- The noise from your PC doesn't enter in your project.
- Your project and the PC have isolated ground.
- Voltage levels of the UART are the same of the power supply of your project.
- Your project is not powered from the USB of the PC, so you don't have power issue when you power off your project.
Technical data
- Original FT231XQ: Compatible with almost all the operating systems and capable of variety baud rates from 300 baud up to 3 Mbaud
- Original Si8642BB-B-IS1: Low-Power Quad-Channel Digital Isolators with isolation rating up to 2.5kV
- Size of 40 x 17 mm
- 4.1 mm isolation between the two sides guarantee an electrical isolation up to 1kV
- Working between 2.5V to 5V.
- TX and RX LEDs indicators.
- Micro USB connector.
- Standard 2.54mm 6 pins female header.
- Protected by a transparent heat shrink sleeve.
Code
Jan 12,2018
1,853 views
Isolated USB to UART Converter with Arduino pro mini connector
2 Layers PCB 97 x 98.7 mm FR-4, 1 mm, 1, HASL with lead, White Solder Mask, Black silkscreen
1853
1
0
Published: Jan 12,2018
BOM(Bill of materials)
Centroid file
Purchase
Donation Received ($)
PCBWay Donate 10% cost To Author
File Last Updated: 2024/02/19 (GMT+8)
File update record
2024-02-1905:20:11
Centroid file is updated.
2024-02-1905:20:11
Parts List (BOM) is updated.
2024-02-1905:20:11
Gerber file is updated.
Only PCB
PCB+Assembly
*PCBWay community is a shared platform and we are not responsible for any design issues.
Copy this HTML into your page to embed a link to order this shared project
Copy
Under the
Attribution-NonCommercial-ShareAlike (CC BY-NC-SA)
License.
Topic
- Comments(0)
- Likes(1)
You can only upload 1 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
Remove
It looks like you have not written anything. Please add a comment and try again.
View More
- Зелинский Владислав Oct 02,2021
View More
VOTING
0 votes
- 0 USER VOTES
0.00
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Design
1/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Usability
2/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Creativity
3/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Content
4/4
More by Simone
You may also like
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
488 0 0 -
RF Control training board for students based on ESP32 C3
647 0 2 -
Aquarius+ Computer, Standard PCB
859 0 4 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
595 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
515 0 1 -
Nintendo Famicom HVC-001 Controller Shells
615 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
573 0 4 -
COMMODORE 128 15KHz DISPLAY ADAPTER (C128 80 COLUMN ADAPTER)
778 1 5 -