IMSAIGUY
UNITED STATES OF AMERICA • + Follow
Edit Project
Tools, APP Software Used etc.
|
EagleAutodesk
|
Description
Microphone Preamp and Processor
I designed this to be a cheap version of the dbx 286s Mic Preamp and Processor. It doesn't all work but the preamp and filters are good. The noise gate needs work. I used the preamp and filter in a project (video below). Maybe you can use the preamp. maybe you can improve the design. There were a couple problems with the Rev A layout but Rev B are the files included here. They fix the problems but were never actually built. The preamp chip used is very good. Below are some videos (there are more on my channel).
Jul 28,2021
2,195 views
Microphone Preamp and Processor
I designed this to be a cheap version of the dbx 286s Mic Preamp and Processor. It doesn't all work but the preamp and filters are good.
2195
4
0
7.00 (1)
Published: Jul 28,2021
Download Gerber file 46
BOM(Bill of materials)
Centroid file
Purchase
Donation Received ($)
PCBWay Donate 10% cost To Author
File Last Updated: 2024/02/29 (GMT+8)
File update record
2024-02-2910:45:10
Centroid file is updated.
2024-02-2910:45:10
Parts List (BOM) is updated.
Only PCB
PCB+Assembly
*PCBWay community is a shared platform and we are not responsible for any design issues.
Copy this HTML into your page to embed a link to order this shared project
Copy
Under the
Attribution-ShareAlike (CC BY-SA)
License.
Topic
- Comments(0)
- Likes(4)
You can only upload 1 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
Remove
It looks like you have not written anything. Please add a comment and try again.
View More
- Ivan Formosa Nov 10,2023
- Engineer Aug 23,2022
- Roman Yanchuk Jan 31,2022
- John John Vu Jul 28,2021
View More
VOTING
1 votes
- 1 USER VOTES
7.00
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Design
1/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Usability
2/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Creativity
3/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Content
4/4
-
8design
-
6usability
-
8creativity
-
6content
7.00
More by IMSAIGUY
- Op-amp Test Board This is a two section board. two dual op-amps can be compared. Half of the device is used in a non-i...
- Linear Optocoupler youtube video will follow in a few weeksnote: pin one of the IC's are square pads, load correctly as...
- I2C 6 Digit Nixie Tube Display YouTube video will follow in a couple weeks
- Gyrator Board circuits from: https://sound-au.com/articles/gyrator-filters.htm
- Transistor Training PC Board youtube video will follow soonPlease don't ask for a BOM or schematic. The board IS the schematic. I...
- LCR Meter PCB Fixture Made for an LCR meter with kelvin 4 BNC fixtures. this is standard spacing of 22mm between connector...
- 8 LED SIP for Protoboard you can build it common cathode or common anode (put the LEDs in backwards)made for 0805 partsconnec...
- 2.4GHz Hairpin Bandpass Filter Designed with Keysight Genesys. If you order this board it must be fabricated with Rodgers 4003C 0.3...
- 2.45GHz YAGI Antenna Design This YAGI design is for 2.45GHz. if you order request: 1mm thick board, no solder mask, black silk s...
- Protoboard Power Connector this connects the power rails together, top and bottom, on a proto boardor just use extra wire for t...
- Analog Prototype board from old HP days Odd board for analog circuits. This is modeled after a board available in the HP stockroom when I wo...
- VNA SMA Calibration Standard Holder VNA SMA Calibration Standard HolderNice way to keep track of all you VNA cal standards
- SMA Thumbwheel Wrench Collar to be used on an SMA connector to provide a way to finger tighten. I have used PLA but I exp...
- Wire Grid Polarizer 5/5 mil wire grid polarizer. tested 1 GHz to 20 GHz
- Salen-Key Filters These filters are from the ARRL Handbook.Low PassHigh PassBand PassBand Reject (Notch)
- Notch Filter I have three videos on this filter:
- Low Pass FIlter RF Ham Radio this is a 40m low pass filter design. other designs can be found in the ARRL handbookthe values uses...
- Tektronix 576 Curve Tracer Test Socket This is a test socket for the Tektronix curve tracer. for TO-99 TO-5 and TO-220 packagesI've include...
You may also like
-
RPI - 8 IO PLC With ATTiny85 Watch Dog
121 0 0 -
Nintendo Famicom HVC-001 Controller Shells
167 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
173 0 2 -
COMMODORE 128 15KHz DISPLAY ADAPTER (C128 80 COLUMN ADAPTER)
200 0 2 -
-
-
-
TEKTRONIX THS710,THS720,THS730 LED Backlight drop in replacement Controller
558 0 0