Description
EO&N CAPACITOR LEAKAGE TESTER
A tester designed to test leakage in capacitors that also serves to reform electrolytic caps. High voltages are involved.
Schematic and Layout
SCHEMATIC
Schematic_Capacitor Leakage Tester V2_2023-01-14.pdf
Jan 14,2023
2,422 viewsReport item
EO&N CAPACITOR LEAKAGE TESTER
2 Layers PCB 57.2 x 85.1 mm FR-4, 1.6 mm, 1, HASL with lead, Green Solder Mask, White silkscreen
A tester designed to test leakage in capacitors that also serves to reform electrolytic caps. High voltages are involved.
2422
6
0
Published: Jan 14,2023
Download Gerber file 56
PCBWay Donate 10% cost To Author
*PCBWay community is a shared platform and we are not responsible for any design issues.
Under the
Attribution-ShareAlike (CC BY-SA)
License.
Topic
- Comments(0)
- Likes(6)
You can only upload 1 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
View More
More by Caldeira
-
Selenium Rectifier and Filter Capacitor replacement PCB's - small size
Selenium Rectifier and Filter Capacitor replacement PCB's - small size
-
Selenium Rectifier and Filter Capacitor replacement PCB's - standard size
Selenium Rectifier and Filter Capacitor replacement PCB's - standard size
-
Decade Resistor Substitution Box
A ver simple and cheap Decade Resistor Substitution Box for your workshop. I used 1% resistors, rate...
-
EO&N CAPACITOR LEAKAGE TESTER
A tester designed to test leakage in capacitors that also serves to reform electrolytic caps. High v...
-
Opto-coupler or relay battery switcher
A battery switcher using Opto-couplers or relays.
-
Full supply board for DIY Tube Tester
A DIY Tube Tester needs a lot of different power supplies to allow you to really test tubes correctl...
-
W224132ASC32_Gerber_PCB_AF RF Active Probe with AGC
A high impedance RF and AF probe with AGC, and selectable gain.
-
A high impedance active RF/AF probe with amplifier.
An RF demodulator probe is a valuable tool for repairing radios and other RF gear. Equally, an audio...
-
Supply board for tube radio bluetooth module with signal booster.
A power supply board for adding a bluetooth module to a tube radio, with signal boost to raise the a...
-
Power Supply Board for Bluetooth module on tube radio
A convenient supply and I/O board for adding a bluetooth module to a tube radio. The bluetooth modul...
-
75 to 300 Ohm L-Pad with switched attenuator.
Allows for switched switchable attenuation steps and impedance matching of the signal generator sign...
-
Gerber_Taper Pad Attenuator
Switched attenuator and impedance matching pad for FM test signals.
-
Gerber_filter_caps_rectifier
Boards to replace filter caps and selenium rectifier in a tube radio.
-
PC Soundcard Oscilloscope Buffer/Attenuator
The video on my channel describes the schematic and the build itself. Find my Youtube channel "Elect...
-
External BFO V2.1 SMD version
I recently restored a Grundig Satellit 2100, which turned out really well, and which can be viewed o...
-
External BFO V2.0 through-hole version
I recently restored a Grundig Satellit 2100, which turned out really well, and which can be viewed o...
-
External BFO V2.0 through-hole version
I recently restored a Grundig Satellit 2100, which turned out really well, and which can be viewed o...
-
Balanced Line Driver
I have on occasion needed a balanced signal to test power amps and so on. This is the second version...
You may also like
-
-
-
-
-
-
-
-
ESP32-S Development Board, in "Arduino Uno" form factor
4143 4 16
