Apple II Gotek Adapter
This adapter uses simple, off the shelf 2.54mm pin headers and sockets to adapt a Shugart style gotek to work with an Apple II. Tested with Apple IIc, IIe, and IIGS (Disk II Mode Only).
On one side of the board solder a 2x17 2.54mm female header and a 1x4 either tall female header or let it sit off the board a mm or 2 for better connection.
The other side gets 2x10 male and 1x2 male. The terminal block is not needed.
Works with .woz, .dsk (rename to .do), .do, or .po apple II disk images when converted to .hfe (ideally .hfe Experimental Rev 3 if you're using the beta software that was released on Christmas 2023). That's it!
I have a pre-converted copy of the latest ProDos in my repo. https://github.com/mudmin/AnotherMaker/tree/master/Apple%20II%20Gotek
Much thanks to Jean-François over at https://hxc2001.com/docs/gotek-floppy-emulator-hxc-firmware/pages/apple.html for the firmware, the conversion, software and the tech support.
Apple II Gotek Adapter
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(2)
- Likes(15)
More by Dan Hoover
-
Engineer's Mini Notebook 555 Circuits by Forrest M. Mims III - PCB #1
PCB #1 IncludesBasic Monostable CircuitBasic Astable CircuitFrequency DividerTouch-Activated SwitchV...
-
Tandy Terminator for the TRS-80 Model II/12/16
The Tandy Terminator for the Model II/12/16 also fits the 16B and 6000, although those machines prob...
-
Epson QX10 YM2149 Sound Card
Recreation of the yamaha sound card for the QX10. Github: https://github.com/brijohn/qx10/tree/maste...
-
Epson QX10 CF Adapter
The QX10 CF adapter allows you to add a solid state drive to your QX10.Github https://github.com/bri...
-
Epson QX-10 Titan Clone
The Titan card allows you to add an 8088 processor to the QX10 to run dos software. It's been repro...
-
EPROM Booster - Program Higher voltage Vintage Eproms on your XGECU T48 / 866ii+
The cheaper XGECU Programmers are not capable of programming EPROMS at higher voltages. Even when yo...
-
PiColeco - Raspberry Pi Pico (Clone) Multicart
Full project details at https://github.com/aotta/PiCOLECO/tree/main?tab=readme-ov-file Thank you to ...
-
WonderTANG 2.0b - Latest version MSX FPGA Cartridge
Note: According to Luis the other board on pcbway is obsolete!This cartridge allows any MSX compute...
-
Engineer's Mini Notebook 555 Circuits by Forrest M. Mims III - PCB #3
This board includes the Event Failure AlarmAudio Oscillator / MetronomeLED FlasherToy OrganSee alsoh...
-
Engineer's Mini Notebook 555 Circuits by Forrest M. Mims III - PCB #2
This board includes the Pulse Generator, Frequency Meter, Bouncefree switch and Voltage Controlled i...
-
RGBtoHDMI Mega Board v2.0
Tested working.This is an update of my https://www.pcbway.com/project/shareproject/RGB2HDMI_Pro_The_...
-
Wemos D1 Maxi - Prototyping shield for the WeMos D1 Mini
This board allows you to connect a WeMos D1 Mini and up to 3 shields to broken out pin headers and s...
-
RGBtoHDMI 4.0 (Latest Version)
Boards are relatively easy to make. They can be made in a toaster oven as I show here. https://www.y...
-
RGB2HDMI Pro! The Ultimate Prototyping Board for RGBtoHDMI
This board is designed be modular so you can use as much or as little as you wantMy video showing th...
-
9 Pin Cable Tester
This simple project just uses a few materials to build a cable tester allowing you to test any combi...
-
Tandy Diagnostic Cartridge for Color Computer 1, 2 and 3 - Coco
Make a simple cartridge to test the basic functionality of your Coco. From ROM to RAM. Video, serial...
-
Apple II Gotek Adapter
This adapter uses simple, off the shelf 2.54mm pin headers and sockets to adapt a Shugart style gote...
-
The $5 XTIDE Card
XTIDE is a great tool for allowing you to use more modern compact flash, sd cards and large hard dri...
-
-
-
-
Tester for Touch Screen Digitizer without using microcontroller
241 2 2 -
Audio reactive glow LED wristband/bracelet with NFC / RFID-Tags
242 0 1 -
-
-
