Description
2.4GHz Hairpin Bandpass Filter
Designed with Keysight Genesys. If you order this board it must be fabricated with Rodgers 4003C 0.32" substrate. No soldermask, no silkscreen, immersion gold plating
the filter is 2.40GHz center 2.3GHz-2.5GHz wide
Sep 19,2023
2,238 views
2.4GHz Hairpin Bandpass Filter
2.4GHz bandpass microstrip hairpin filter 200MHz width
2238
4
0
Published: Sep 19,2023
Standard PCB
Download Gerber file 33
PCBWay Donate 10% cost To Author
Only PCB
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Under the
Attribution-ShareAlike (CC BY-SA)
License.
Topic
- Comments(0)
- Likes(4)
Upload photo
You can only upload 5 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
More by IMSAIGUY
-
Op-amp Test Board
This is a two section board. two dual op-amps can be compared. Half of the device is used in a non-i...
-
Photodiode Amplifier with Gain Settings
just a fun project, 4 gain settings transimpedance amp
-
Tiny RS232 Monitor
YouTube videos describe the circuit. The Rev B board fixes the ground problem and correctly connects...
-
Kaypro ROM Selector Board
Here is my video on the project
-
SDK85 8755 EPROM Adapter
A youtube will follow to explainThis is pin compatible with an 8755 chip which is ROM and I/O. This ...
-
7414 Fast Edges
I've done a couple videos on this subject
-
EL2018 EL2252 board for HP 3458A
Here is how it was done by Agilent. Note: the +V is different between the two EL2018. one uses +15 a...
-
Small Gear Motor Housing
This is a 3D print file for a housing/mount for small gear motors. the motor slides into the housing...
-
Panaplex Display Board
this project is documented on YouTube
-
ATTINY ETC board for ETW-3800 Microprocessor Trainer
this board fits the Heathkit ETW-3800 trainer. it has I2C breakout chips to allow lots of IO to conn...
-
Narrow SO-20 to DIP Adapter
this results in a 0.300" DIP for protoboardsit also includes a spot for a bypass capacitor to be use...
-
Narrow SO-16 to DIP Adapter
the DIP has a 0.300" size for protoboard maximization
-
Tiny IMSAI 8080 Computer
This uses an ATTINY814 microcontroller and a bunch of 74595 shift registers to flash the LEDs and re...
-
Narrow SO-14 SMD to DIP Adapter
I made this for using Attiny414 814 type devices on a protoboard with only 0.3" of width
-
Digital Capacitor Bandpass Filter
uses PE64012 serial programmable digital capacitorhttps://youtu.be/zgKv5fhoEHI
-
Mini-Circuits MAR MMIC Amplifier
When ordering board, choose 0.8mm thickness. This is correct thickness for 50ohm transmission line.R...
-
Weinschel Programmable Attenuator
YouTube video series describes project
-
Electrical Symbol Drafting Stencil
I wanted a drafting template for use with a Micron 08 pen. I had this made with 2.5mm thick clear ac...
You may also like
-
-
mammoth-3D SLM Voron Toolhead – Manual Drill & Tap Edition
262 0 0 -
-
-
-
Tester for Touch Screen Digitizer without using microcontroller
472 2 2 -
Audio reactive glow LED wristband/bracelet with NFC / RFID-Tags
419 0 1 -
-
