Description
2.45GHz YAGI Antenna Design
This YAGI design is for 2.45GHz. if you order request: 1mm thick board, no solder mask, black silk scrren
Jun 08,2023
1,217 views
2.45GHz YAGI Antenna Design
just what is says
1217
2
0
Published: Jun 08,2023
Download Gerber file 15
Purchase
Donation Received ($)
PCBWay Donate 10% cost To Author
*PCBWay community is a shared platform and we are not responsible for any design issues.
Copy this HTML into your page to embed a link to order this shared project
Copy
Under the
Attribution-ShareAlike (CC BY-SA)
License.
Topic
- Comments(0)
- Likes(2)
You can only upload 1 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
Remove
It looks like you have not written anything. Please add a comment and try again.
View More
VOTING
0 votes
- 0 USER VOTES
0.00
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Design
1/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Usability
2/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Creativity
3/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Content
4/4
More by IMSAIGUY
- Op-amp Test Board This is a two section board. two dual op-amps can be compared. Half of the device is used in a non-i...
- Linear Optocoupler youtube video will follow in a few weeksnote: pin one of the IC's are square pads, load correctly as...
- I2C 6 Digit Nixie Tube Display YouTube video will follow in a couple weeks
- Gyrator Board circuits from: https://sound-au.com/articles/gyrator-filters.htm
- Transistor Training PC Board youtube video will follow soonPlease don't ask for a BOM or schematic. The board IS the schematic. I...
- LCR Meter PCB Fixture Made for an LCR meter with kelvin 4 BNC fixtures. this is standard spacing of 22mm between connector...
- 8 LED SIP for Protoboard you can build it common cathode or common anode (put the LEDs in backwards)made for 0805 partsconnec...
- 2.4GHz Hairpin Bandpass Filter Designed with Keysight Genesys. If you order this board it must be fabricated with Rodgers 4003C 0.3...
- 2.45GHz YAGI Antenna Design This YAGI design is for 2.45GHz. if you order request: 1mm thick board, no solder mask, black silk s...
- Protoboard Power Connector this connects the power rails together, top and bottom, on a proto boardor just use extra wire for t...
- Analog Prototype board from old HP days Odd board for analog circuits. This is modeled after a board available in the HP stockroom when I wo...
- VNA SMA Calibration Standard Holder VNA SMA Calibration Standard HolderNice way to keep track of all you VNA cal standards
- SMA Thumbwheel Wrench Collar to be used on an SMA connector to provide a way to finger tighten. I have used PLA but I exp...
- Wire Grid Polarizer 5/5 mil wire grid polarizer. tested 1 GHz to 20 GHz
- Salen-Key Filters These filters are from the ARRL Handbook.Low PassHigh PassBand PassBand Reject (Notch)
- Notch Filter I have three videos on this filter:
- Low Pass FIlter RF Ham Radio this is a 40m low pass filter design. other designs can be found in the ARRL handbookthe values uses...
- Tektronix 576 Curve Tracer Test Socket This is a test socket for the Tektronix curve tracer. for TO-99 TO-5 and TO-220 packagesI've include...
You may also like
-
RPI - 8 IO PLC With ATTiny85 Watch Dog
132 0 0 -
Nintendo Famicom HVC-001 Controller Shells
176 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
174 0 2 -
COMMODORE 128 15KHz DISPLAY ADAPTER (C128 80 COLUMN ADAPTER)
209 0 2 -
-
-
-
TEKTRONIX THS710,THS720,THS730 LED Backlight drop in replacement Controller
563 0 0