Popular: Arduino Automation Commodore Iot Raspberry pi
Projects 2412
Questions 55
Feedback 962
Blog 23
Sponsorships 118
tükörteszter_arduino_new
Feb 04,2023
Mirror tester for projects
455
0
0
nanBluino - DIY Arduino Nano USB Type-C
Bluino Feb 04,2023
Overview"Arduino is an open-source electronics prototyping platform based on flexible, easy-to-use hardware and software. It's intended for artists, designers, hobbyists, and anyone interested in creating interactive objects or environments."This tutorial will take you through all the steps to build an Arduino Nano compatible "nanoBluino" and how to install smd components using solder paste and stencil techniques.Make special of nanoBluino special is that it uses the USB socket type C.Bill of Ma...
Arduino arduino nano DIY
3769
1
5
Sumo Robot Nasıl Yapilir
Nejdat delioğlu Feb 01,2023
Bu projenin gerber dosyasini indirip sizde yapabilirsiniz
3D printing SLA Arduino
1046
0
0
MX29F1615 EEPROM programmer based on an Arduino Mega 2560 (Commodore Amiga Kickstart)
kinmami Feb 01,2023
MX29F1615 (16 bit EEPROM) programmerBased onhttps://framagit.org/acathla/eeprom-programmerandhttps://dragaosemchama.com/en/2016/10/arduino-mega-eprom-programmer/DISCLAIMER·        Gerber and Centroid files, BOM list are subject to change without notice.·        The project is tested with the latest firmware (stable) version available at the time of writing.
Amiga Commodore Hardware
3107
0
11
X27 Stepper Gauge PWM ATtiny85
Pena Jan 30,2023
Board to control an x27 motor using an LS PCM signalInput 12-30v and outputs 5v for the ATtiny85 that controls the motorInput for the PWM needs to be around 12-16 volts, this will be lowered to 5v(or less) for the ATtiny to read.X27 stepper motor is to be mounted on the back for better clearance, the circuit is on the front side.Pretty easy setup, solder all the parts, and program using the headers(right side of the pcb) and an Arduino UNO as an ISP, and boom, it's ready to go.I programmed the t...
Arduino DIY automobile
1425
0
0
8-ch N-Mos Breakout
MakerIoT2020 Jan 27,2023
8Ch NMOS Breakout ModuleAs a companion module to my recently published 8Ch PMOD breakout board,I decided to do a similar PCB, but with NMOS devices instead. This opens up more possibilities for proper testing and prototyping, as PMOS and NMOS devices has different use applications, and most importantly, can sometimes even be combined for a particular purpose, like an H-Bridge motor driver, for example.8Ch NMOS BreakoutWhat is on the PCB?As NMOS devices function quite differently from their PMOS ...
NMOS breakout Arduino ESP32
954
0
1
POWER BLOCK Version 2
Arnov sharma Jan 27,2023
Hey guys how you doing.POWER BLOCK is a DIY UPS with emergency lighting that can be utilized to power a variety of 5V-operated devices, like a raspberry pi, or an Arduino project, or even to charge gadgets like a tablet or smartphone. It can also be used outside for lighting.The objective was to construct a battery system that could be used outside during a brief camping trip to charge cellphones and other 5V gadgets as well as serve as an emergency light.The heart of this project is this B...
3D printing SLA DIY
879
0
0
Arduino Modular
Quilaguilque Jan 27,2023
aplaca para conectar arduino y sensores o actuadores
472
0
0
8Ch P-Channel-Mosfet-Breakout
MakerIoT2020 Jan 26,2023
8-Ch P-Mos BreakoutWhile prototyping our projects, we Makers often need to interface devices with a higher current draw, like motors, or RGB lights, to our microcontrollers. These typically are unsuitable for connecting directly to an Arduino, ESP32 or Raspberry Pi’s GPIO pins. This is usually the time when we start grabbing transistors or MOSFETs.While I normally keep a few leaded transistors and MOSFETs in the lab, These are not always convenient to use, as they may be in big packages or have ...
MOSFET Breakout board Arduino
3501
1
1
Pi Pico Breakout Board
Reboot Jan 23,2023
This breakout board provides labeled RPi headers including extra 3.3V, VBUS and GND pins.Two rows of headers can be used for male/female 2.54mm headers or 2.54mm pitch screw terminals.The module can be surface mount soldered to the breakout board, or through hole headers can be used to plug in the Pi Pico.There is a 3 pin SWD header for optional access to that port.There is also a power LED and a convenient reset button for the Pi Pico.
Arduino Raspberry pi Development Board
2431
0
5
1 ... 82 83 84 85 86 87 88 89 90 91 92 ...
Popular Creator
PUEYO MUÑOZ
Excellent Engineer
Project: 7 Followers: 28
Green Energy
Excellent Engineer
Project: 23 Followers: 436
jjaime68
Excellent Engineer
Project: 1 Followers: 4
König
Excellent Engineer
Project: 5 Followers: 109
Casimiro
Excellent Engineer
Project: 6 Followers: 467
Popular Project
A Modified zFlip 5
With many Samsung zFlip phones hitting the unfortunate fate of a broken folding screen, I took it as an opportunity to build my own silly phone. Taking only the minimum parts required for the phone to...
ESP32-BlueJammer
The ESP32-BlueJammer (Bluetooth jammer, BLE jammer, WiFi jammer, RC jammer) disrupts various devices using an ESP32 and nRF24 modules, causing plenty of noise and sending unnecessary packets (DoS).It ...
Air Quality Monitor
The Air Quality Monitor is a compact, ESP32-C3–based device designed to track and display key indoor environmental metrics in real time. At its core, it integrates the Sensirion SEN54 for particulate ...
DIY Meshtastic Using ESP32 : Build Your Own Private Off-Grid Network
Project OverviewThis project delivers a complete, custom-designed PCB solution for building Meshtastic mesh network nodes. Unlike traditional communication methods that rely on cellular towers or Wi-F...
Jammer Bluetooth 2.4G
Proyecto de PCB para Jammer bloqueador inhibidor de señales Bluetooth y Wifi de 2.4G.Proyecto patrocinado por PCBWay, muchas gracias por el apoyo!Primero regístrate en PCBWay haciendo clic acá, luego ...
View More
Hot Project Tags
Space Exploratio Virtual reality Microcontroller DIY Synthesizer Weather Station Synthesizer Antenna TVC