|
KiCADKicad
|
MAX8815 step up converter
OVERVIEW
Max8815 board is Step-up converter based on MAX8815.
The project is designed according to MAX8815 data sheet:
https://datasheets.maximintegrated.com/en/ds/MAX8815A.pdf
This circuit is useful for powering a 3.3v - 5v circuit (such as a microcontroller) through a lower voltage battery, such as: lithium cell, LTO cell, Ni-cd, etc ...
Max8815 is a high efficiency circuit: this feature is essential in a battery powered system, where every single mA saved is important for the battery life!
I decided to share this project to allow everyone to use, try and experience the MAX8815 IC.
The project is shared on Github and open to modifications and improvements.
The circuit has the following features:
Input: 1.5V - 5V
Output: 5V fixed or 3.3V - 5V (adjustable).
The max output current depends on input voltage. the board goes into protection when the input current exceeds 1A
INSTRUCTIONS
5V Fixed output:
- Set J3 shunt to "OFF" position
- Set J4 shunt to "Normal" position
- Set J5 shunt to "5v" position
- Connect Input power supply (range 1,5v - 5v)
- Set J3 shunt to "ON" position
- Check D1 led lights ON
- Connect the output load
Adjustable output:
- Set J3 shunt to "OFF" position
- Set J4 shunt to "Normal" position
- Set J5 shunt to "Adj" position
- Connect Input power supply (range 1,5v - 5v)
- Set J3 shunt to "ON" position
- Check D1 led lights ON
- Set the output voltage (from 3,3v to 5v) by RV1 potentiometer
Other settings:
By J4 shunt it is possible to set "FPWM" mode according to MAX8815 data sheet
OPENSOURCE HARDWARE CERTIFICATION
Max8815 board has been certified as open source hardware by the Open Source Hardware Association, with the UID: IT000008.
MAX8815 step up converter
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(1)
- Engineer Apr 11,2023
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Sergio Ghirardelli
- Wemos as ISP Wemos as ISP is an interface card that plugs into Wemos mini board ESP8266, to allow the programming...
- Stop if Crash! Microcontrollers can crash.This can happen for sketch mistakes, but also for failures in the microco...
- OpticalShow card PCB OpticalShow is a system that uses optical fibers to transmit the light emitted by an RGB LED matrix....
- OpticalShow mask OpticalShow is a system that uses optical fibers to transmit the light emitted by an RGB LED matrix....
- Green Detect - Wireless Sensor Network Platform Wireless Sensor Network Platform (WSN) , for enviromental monitoring.DescriptionGreen Detect project...
- MAX8815 step up converter OVERVIEWMax8815 board is Step-up converter based on MAX8815.The project is designed according to MAX...
- Green BMS Interface board v.0.1 Green BMS is an open source Smart Battery Management System for Lithium battery Cells.Green BMS proj...
- Green BMS Cell Module v.0.2 Green BMS is an open source Smart Battery Management System for Lithium battery Cells.Green BMS proj...
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
346 0 0 -
RF Control training board for students based on ESP32 C3
463 0 2 -
Aquarius+ Computer, Standard PCB
658 0 3 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
478 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
422 0 0 -
Nintendo Famicom HVC-001 Controller Shells
517 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
493 0 4 -
COMMODORE 128 15KHz DISPLAY ADAPTER (C128 80 COLUMN ADAPTER)
631 1 4 -