Popular: Arduino Automation Commodore Iot Raspberry pi
Projects 2579
Questions 55
Feedback 993
Blog 23
Sponsorships 136
7 segment with 7 Servo / 7 Segment mit 7 Servos / Siebensegmentanzeige
Emmering Jul 27,2023
Siebensegmentanzeige mit 7 ServosBenötigte Bauteile:7x 1/4W 220 Widerstand, Kohleschicht, 220 Ohm14x LED weiß, 3 mm7x TowerPro SG90 Servomotor1x Arduino Uno Rev31x DC-DC Buck Converter Adjustable Mini Step-down Module 1.8V 3.3V 5V 9V 12V 2A3D Druck Dateien: https://www.printables.com/de/model/362886-7-segment-mit-7-servosCode: https://github.com/18-Sunil-18/7_segment_with_7_Servo
3D printing Arduino DIY
1715
0
2
Simon Says Game Shield Arduino
Astoraque Duran Jul 26,2023
Simon Game Arduino ShieldEn este video, veremos cómo programar un juego clásico como lo es Simon el juego de la memoria. Lo haremos en un formato Shield compatible con Arduino UNO y MEGA. Veremos el circuito, y la programación
SIMON GAME SHIELD ARDUINO
3289
0
1
PT226x Remote v1.1
Mackey Jul 23,2023
This is a remote encoder board that supports several versions of PT226x encoder chips in a number of configurations.Note that the components needed varies based on the configuration. The components list above is as-needed per your configuration. See configuration notes below.Encoder ChipThe voltage being supplied and/or how the encoder is being controlled, determines which encoder chips are better suited. For low voltage operation the PT2260-R4S is the choice because it can run on...
Arduino Remote Remote Control
2044
0
1
TechsPassion Starter Shield
TechsPassion Jul 21,2023
This is the PCB file for the TechsPassion Starter Shield
Arduino DIY LED
889
0
0
Arduino NANO based Prop Controller
Jul 21,2023
This is an Arduino NANO based Prop Controller for Halloween or other occasions.It can be built up in multiple ways and supports audio playback from a DFPlayer Mini module.It can drive up to 3 servos, 2 relays and 3 high-current loads via MOSFETs.It can wake on PIR and can sample analog inputs too.
Arduino DIY PCB
2550
1
4
WLED controller
Jul 21,2023
This is a small WLED controller for driving 4 LED's from a 5V input supply.It can be setup as RGBW or as 4 separate LED's. These are all fed from MOSFET's so can be high powered LED's.This is used in my Halloween prop controllers to turn on lights and create strobe lights.All of my projects are available here:https://www.youtube.com/@scaresandsparks/videos
Arduino ESP8266 DIY
1943
0
1
WEMOS Environmental monitor board
GS Jul 21,2023
An environmental monitoring board to allow environmental conditions to be monitored.I built this to monitor conditions in my greenhouse, including air temperature and humidity, soil temperature, and soil moisture.
Greenhouse arduino home automation
1242
0
0
ArduboyOLEDI2C
Fareed Read Jul 20,2023
Ini merupakan rangkaian dari ArduBoy versi Arduino Nano atau Arduino Uno dengan menggunakan display OLED I2CUntuk Selengkapnya bisa dilihat di blog Fareed Read's Electronics Untuk video tutorialnya bisa dilihat dibawah iniUntuk library Arduboy2 versi Arduino Nano dan OLED I2C bisa di download di github inihttps://github.com/harbaum/Arduboy2Kumpulkan Game Arduboy dari TeamARGhttps://github.com/orgs/Team-ARG-Museum/repositories?page=1
Arduino DIY Hardware
3292
0
8
MT36808 Mini Boost Converter
Lam Jul 20,2023
Hi!This is a miniature boost converter board that I made for a Arduino Lipo Charging ShieldA lot of applications require 5V, and 1-cell lipo batteries only produce 3.7V which is why I decided to make a boost.I've experimented with the castellated pads and non-castellated version in previous revisions.This version is castellated, but you can visit my Flux project repo for the non-castellated version.Castellated definitely looks cool and also makes it easy to SMD solder if you can afford the extra...
Development Board Arduino Battery
1536
0
1
TRRS Audio Jack Breakout Board 3.5mm PJ320A or PJ320D
Reboot Jul 17,2023
To easily hook up 3.5mm audio cables to a breadboard project, this breakout PCB can have either a PJ320A or PJ320D (through hole or surface mount) TRRS jack soldered.The jacks are wired in parallel and connected to a 4 pin 2.54mm pitch header. Only one jack should be populated at a time unless intentionally connecting something in parallel.This pcb is intended to be hand soldered as a hobby project.
Arduino Audio TRRS 35mm jack breakout board
5144
0
4
1 ... 84 85 86 87 88 89 90 91 92 93 94 ...
Popular Creator
Jason
Excellent Engineer
Project: 10 Followers: 4
König
Excellent Engineer
Project: 5 Followers: 112
Casimiro
Excellent Engineer
Project: 6 Followers: 489
YT
Excellent Engineer
Project: 8 Followers: 14
Cappa
Excellent Engineer
Project: 1 Followers: 0
Popular Project
DIY Active FFB Pedal PCBA
Easy one click ordering of Ghilipert PCAB V2.2 REV BNo solderinghttps://github.com/gilphilbert/DIY-Sim-Racing-FFB-Pedal-PCBsAsk for part 25 : SQP5W-5Ω±5%-9MMore info here :https://youtu.be/PMupeveZSFM...
4G Hacker Phone
Have you always wanted an easier to use and more powerful Flipper Zero?Are you tired of getting detained by the TSA because of your WiFi hat on your Flipper Zero? Then this is the solution for you. It...
SensWear: An Open-Source, Modular, AI-Ready Wearable Platform
SensWear is an open-source, modular wearable development platform that gives researchers, engineers, and makers control over their hardware, firmware, and raw sensor data. It combines a flexible main ...
DIY XBOX Controller
Greetings everyone, and welcome back. Here's something fun and custom.This is my version of an Xbox controller, which I built from scratch. It features an ESP32-C6 DevKit as the main MCU, paired with ...
Programmable Mist Maker - XIAO / QT PY Extension
This is an open source, programmable mist maker built as an expansion board for the Seeed Studio XIAO ESP32-C6. It mounts directly on the XIAO or QT PY, is powered over USB-C, and turns a piezo atomiz...
View More
Hot Project Tags
Space Exploratio Virtual reality Microcontroller DIY Synthesizer Weather Station Synthesizer Antenna TVC