Popular: Arduino Automation Commodore Iot Raspberry pi
Projects 2581
Questions 55
Feedback 993
Blog 23
Sponsorships 136
UCA Board
Campus SophiaTech Bat Forum Jan 29,2018
### DESCRIPTION80 * 34mm Integrated board for LoRa communication.The antenna can now be adjusted for EU868, US915 and AS923 bands### TECHNICAL DETAILS / COMPONENTSThe board integrate a LoRa transciever (RFM95 from HopeRF), an Arduino Mini Pro and a 868-915MHz antenna.Warning : the antenna has to be adjusted for the different band, as shown in the github.### LEARN / TOPIC / BUILD INSTRUCTIONSAll info are available here :https://github.com/FabienFerrero/UCA_Board
lorawan lora Arduino
4441
0
2
line_sen2
Jakub Mimlich Jan 24,2018
### DESCRIPTIONModular line follower sensor, more description will be add in few days### TECHNICAL DETAILS / COMPONENTSOnly SMD component board, hard to DIY at home.### LEARN / TOPIC / BUILD INSTRUCTIONS10x IR Tx and Rx sensors, 12ch ADC 10b converter running on I2C communication.
Arduino
1802
0
2
Arduino LED power switch
Jakub Mimlich Jan 24,2018
### DESCRIPTIONBoard using power mosfet and shift registers to switch higher load on the output### TECHNICAL DETAILS / COMPONENTSbasic THT assemlby requiring### LEARN / TOPIC / BUILD INSTRUCTIONS
Arduino
1668
0
0
Isolated USB to UART Converter with Arduino pro mini connector
Simone Jan 12,2018
This project is available on KickStarter!https://www.kickstarter.com/projects/1351830006/isolated-usb-to-uart-converter-for-arduino-pro-minDescriptionIt's a USB to UART converter with a digital isolator at the UART side.It has a micro USB for connecting to the PC and a 6 pin header with the same pin-out of the Arduino Pro mini board.The chip FT231XQ is used as interface between the USB and the UART protocol, while the Si8642 is used for isolate the board from the PC.This conv...
mini RS232 UART
2911
0
2
ARDUINO DMD & Sensor Shield
ANWAR Jan 11,2018
### DESCRIPTIONARDUINO DMD Shield For P10 Led Matrix PanelCompatible for ARDUINO NANO, UNO & MEGAinclude:- IR Remote Receiver- DS18B20 Temp Sensor- Bluetooth HC-05 Port- RTC DS3231 Port- DHT11 Humidity SensorVery Easy for Use, Just Plug & Play### TECHNICAL DETAILS / COMPONENTS### LEARN / TOPIC / BUILD INSTRUCTIONS
DMD SHIELD
5489
3
6
Arduino ProMicro Breakout for servo and Screw Connectors
MAURICIO?AURELIO?JABUR Jan 07,2018
### DESCRIPTIONBoard designed for Arduino Pro Micro to use with servo motors, GVS sensors or screw terminals
Arduino pro micro GVS
2880
0
3
Telegram Garden System
Arsana Dec 28,2017
With this system, you can be able to monitor your garden such as soil moisture, temperature, humidity and of course you can control the water pump for irigation with telegram chat application. It use ESP8266 12E for controller, DHT11 for temperature and humidity sensor, and Capacitive soil moisture sensor. You can program this project by arduino software with ESP8266 core in it.Part list :ESP8266DHT115V Relay5V BuzzerPC8173mm LEDAMS1117 3V3Transistor 3904Tactile buttonCapacitor 10uF/16VTermina...
telegram esp8266 iot
5375
4
11
CloudX SoftCOM1
Olayiwola Dec 16,2017
### DESCRIPTIONCloudX softcard is a USB to serial device that allows communication between two devices  e.g PC and MCU. The softcard uses the ft232 FTDI chip. ### TECHNICAL DETAILS / COMPONENTSIt uses FTDI chip with a connector pin that makes it compatible with CloudX controllers ### LEARN / TOPIC / BUILD INSTRUCTIONSIt can be use for different projects just like the Arduino 
Robotics Arduino Micro controller
1935
0
0
Escorna CPU 2.12
Rosas Dec 11,2017
What is an Escornabot?Escornabot is an open source/hardware project that aims to bring robotics and programming to children.The basic Escornabot can be programmed with the robot’s buttons to execute sequence of movements. From this, imagination is the only one limit to the possibilities.- Hey! That you are describing looks very much like a Bee-Bot!- Yes, but much better for several reasons. Among them, I will highlight a few:It is made by you. And your pupils, child...
cc BY-SA 4.0 open arduino
7956
8
16
TrackerV1.1BatLevel(53x54)
Jamshid Dec 10,2017
### DESCRIPTIONA GSM Tracker with STM Processor.Uses AI A7 GSM/GPS Module along with memory cardSerial 1 is for GPS,Serial 2 is for GSMSD Card is on SPI### TECHNICAL DETAILS / COMPONENTSSTM32AI A7 ModuleAll Resistors are 1K SMD ### LEARN / TOPIC / BUILD INSTRUCTIONS
Arduino STM32 GSM Tracker
1746
2
1
Popular Creator
DAS
Excellent Engineer
Project: 53 Followers: 117
🙂
Excellent Engineer
Project: 86 Followers: 59
Casimiro
Excellent Engineer
Project: 6 Followers: 489
YT
Excellent Engineer
Project: 8 Followers: 14
Cappa
Excellent Engineer
Project: 1 Followers: 0
Popular Project
DIY Active FFB Pedal PCBA
Easy one click ordering of Ghilipert PCAB V2.2 REV BNo solderinghttps://github.com/gilphilbert/DIY-Sim-Racing-FFB-Pedal-PCBsAsk for part 25 : SQP5W-5Ω±5%-9MMore info here :https://youtu.be/PMupeveZSFM...
4G Hacker Phone
Have you always wanted an easier to use and more powerful Flipper Zero?Are you tired of getting detained by the TSA because of your WiFi hat on your Flipper Zero? Then this is the solution for you. It...
SensWear: An Open-Source, Modular, AI-Ready Wearable Platform
SensWear is an open-source, modular wearable development platform that gives researchers, engineers, and makers control over their hardware, firmware, and raw sensor data. It combines a flexible main ...
DIY XBOX Controller
Greetings everyone, and welcome back. Here's something fun and custom.This is my version of an Xbox controller, which I built from scratch. It features an ESP32-C6 DevKit as the main MCU, paired with ...
Programmable Mist Maker - XIAO / QT PY Extension
This is an open source, programmable mist maker built as an expansion board for the Seeed Studio XIAO ESP32-C6. It mounts directly on the XIAO or QT PY, is powered over USB-C, and turns a piezo atomiz...
View More
Hot Project Tags
Space Exploratio Virtual reality Microcontroller DIY Synthesizer Weather Station Synthesizer Antenna TVC