Popular: Arduino Automation Commodore Iot Raspberry pi
Projects 527
Questions 15
Feedback 214
Blog 15
Sponsorships 28
CYBER.PY Zero-Three
Arnov sharma Jun 25,2024
Greetings everyone, and welcome back.This is CYBER.PY Zero-Three, a Cyberdesk-themed Raspberry Pi PC that is equipped with the Waveshare 7.9-inch ultra-wide HDMI display.This is basically another installment of my previous Cyber.PY projects, which you can see by visiting the links below.https://www.hackster.io/Arnov_Sharma_makes/cyber-py-zero-one-339846https://www.hackster.io/Arnov_Sharma_makes/cyber-py-zero-two-fdd889First, the whole design was modeled in Fusion360. Then it was 3D printed ...
3D printing Commodore SLA
1974
0
7
Raspberry Pi 4B/5 Current Sensor HAT
Jun 22,2024
A current sensor HAT for Raspbery Pi 4B/5
766
0
0
rpitx-coax-pcb-GP1212-GP731
Yatsevich Jun 22,2024
GitHub project page | rpitx-coax-pcbExpansion board for Raspberry PI allowing to use coaxial SMA output instead of direct wire connection to GPIO to connect radio equipment (antennas, amplifiers, switches, etc.) when working with the rpitx package.The PCB is installed by attaching to the GPIO of the Raspberry PI and can be additionally fixed by using the holes on the Raspberry PI and expansion board side.Basic device characteristics:PCB versions: PCB_rpitx-coax-pcb-GP1212-GP731 - ...
RaspberryPI rpitx Radio
1195
0
0
rpitx-coax-pcb-NOFILTER
Yatsevich Jun 22,2024
GitHub project page | rpitx-coax-pcbExpansion board for Raspberry PI allowing to use coaxial SMA output instead of direct wire connection to GPIO to connect radio equipment (antennas, amplifiers, switches, etc.) when working with the rpitx package.The PCB is installed by attaching to the GPIO of the Raspberry PI and can be additionally fixed by using the holes on the Raspberry PI and expansion board side.Basic device characteristics:PCB versions: PCB_rpitx-coax-pcb-NOFILTER - no f...
RaspberryPi rpitx Radio
715
0
0
KY-022 Infrared Receiver Module
BARMAN Jun 21,2024
The KY-022 module is an infrared receiver that reacts to 38kHz IR light. It can be used to receive commands from IR remote controllers for TVs, stereos, and other IR transmitter devices. The module provides digital output signals that can be easily interfaced and read by microcontrollers such as Arduino, Raspberry Pi, ESP32, etc. Read continue (schematic, how it works, connection guides, etc.) - KY-022 Infrared Receiver Module.Parts Placement Instructions for PCB:VS1838B IRSMD 595nm Red LED1k Re...
Arduino ESP8266 DIY
3432
0
0
POWER Pi Version 2
Arnov sharma Jun 20,2024
Greetings to everyone, and welcome back.This is Power Pi, a small, integrated Raspberry Pi PC with a built-in lithium-ion battery pack that allows the Pi to be powered wirelessly.This is version 2 of the previously built Power Pi project.In the previous version, there were only two sections: the battery section and the Pi holder. In the new version, we have added a few more sections, which results in a somewhat larger setup than the one previously.We also included an RGB LED setup in this b...
3D printing SLA Arduino
1865
0
3
Raspberry Pi Pico Tire/Tyre Pressure Monitoring System (TPMS)
Teel Jun 15,2024
The Tire light was illuminated on the dash of my 2007 Prius. I ran around checking the air pressure in the tires. Found that a few were perhaps a little low, but not enough to cause the dash light to be lit. I then assumed that one ore more of the TPMS sensors had a dead battery, but how can I know for certain? I took it to the garage and found that yes, one was dead and one had a low battery. The garage replaced them both. This got me to look and see if anyone had built a TPMS display to show t...
Raspberry pi DIY Circuit
3262
0
1
C64 Pico Cart
Secco41 Jun 07,2024
Thanks to cknave for the project, Not tested and I will try and share comments about this project.
Commodore Raspberry pi Retro
1664
0
6
Probe Connector to interface with Breadboard for Raspberry Pi Pico Debug Probe
HARAN Jun 06,2024
This connector PCB is used to connect the Raspberry Pi Pico Debug Probe to the Breadboard. (It is actually used to connect the Probe Plug)Raspberry Pi Pico Debug Probe and Probe Plug are the other project.
DIY Raspberry pi
872
0
0
Home Automation System
Sarthak Jun 03,2024
This is a Home Automation node connected to Raspberry Pi 4 using Home Assistant along with MQTT protocol. It has 4 channel relay connected parallel to electrical switches which are connected to electrical appliances. This basically makes the appliance controllable by this device as well as normal switches in case of any failure. DHT11 is used to give temperature readings to the Home Assistant dashboard. The LED in front lights up in case of any error or if there is an internet outage. This is my...
KiCad Design Contest-Communication Theme ESP8266 Home Automation
2007
0
1
1 ... 12 13 14 15 16 17 18 19 20 21 22 ...
Popular Creator
Pmanapon
Excellent Engineer
Project: 1 Followers: 15
hackup.net
Excellent Engineer
Project: 17 Followers: 123
Anthony Chiam
Excellent Engineer
Project: 1 Followers: 6
McAleer
Excellent Engineer
Project: 2 Followers: 9
agoktugaydin
Excellent Engineer
Project: 2 Followers: 6
Popular Project
AERIS-10 Open Source Phased Array Radar
The AERIS-10 is a low‑cost open‑source phased‑array radar platform designed for makers, researchers and educators. Operating around 10.5 GHz, the system can detect and track multiple objects at ranges...
4G Hacker Phone
Have you always wanted an easier to use and more powerful Flipper Zero?Are you tired of getting detained by the TSA because of your WiFi hat on your Flipper Zero? Then this is the solution for you. It...
Project Aura AQ Sensor Hub PCB v1.1
This is the custom PCB for Project Aura AQ, an open-source ESP32-S3 air-quality monitor with touchscreen UI, local web dashboard, MQTT, and Home Assistant support.What is included on the PCB:- Built-i...
Simple lo-fi offline MP3 player for the Zion Brock vintage radio (official PCB)
Offline | Mono | Lo-FiThe PCB version of the Vintage Radio does not receive live radio signals. It is a self-contained offline music player. You load albums or tracks onto a microSD card, insert ...
DIY Active FFB Pedal PCBA
Easy one click ordering of Ghilipert PCAB V2.2 REV BNo solderinghttps://github.com/gilphilbert/DIY-Sim-Racing-FFB-Pedal-PCBsAsk for part 25 : SQP5W-5Ω±5%-9MMore info here :https://youtu.be/PMupeveZSFM...
View More
Hot Project Tags
Space Exploratio Virtual reality Microcontroller DIY Synthesizer Weather Station Synthesizer Antenna TVC