PocketScroller
What is it?
It's a cape for the PocketBeagle that provide 6 HUB75 output connectors for driving standard P10/P5 panels.
Why did you make it?
P10 and P5 LED panels have become a popular method of displaying images, text, and effects for animated Christmas Light displays. Traditionally, the community has been using an "Octoscroller" on a full Beaglebone Black for driving the panels. This cape provides much of the same functionality, but for the smaller/cheaper PocketBeagle.
What makes it special?
The PocketScroller has 6 output connectors, each of which can drive more that 12 P10 1:8 scan panels for a total panel count of 72. It supports the 1:4 scan P10 panels, 1:8 scan P5 panels, and 1:16 scan P5 panels. Other panels types that use the 1:8 or 1:16 scan rates are also supported.
The FPP software that runs on the PocketBeagle is capable of playing sequences off the local SD card, but can also accept e1.31 or DDP data via a network adapter plugged into the USB port. (WIFI or Ethernet) Any software that can output e1.31 should be able to send effects to the PocketScroller for display on the Panels.
The FPP software uses both PRU's on the PocketBeagle to drive the panels. This allows a very high refresh rate while freeing up the main CPU to handle the network IO and general panel layout.
All software and PRU code is open source and available on github.
The cape provides:
6 HUB75 output connectors
USB-A connector for a USB ethernet or wifi adapater
3.5mm screw terminal for providing 5v power. This provides power to the PocketBeagle, the buffer chip, and the USB bus.
You will need:
A good quality SD card with the latest FPP image installed on it. The latest FPP images can always be found at http://dankulp.com/bbb/
A USB network adapter - ethernet is preferred for initial setup, but WIFI (adapter must be supported by Linux/Beaglebone/Raspberry Pi) can also work if you use a micro-usb cable to connect to the PocketBeagle to do the WIFI setup.
PocketScroller
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(3)
- 2 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
-
9design
-
9usability
-
9creativity
-
10content
-
10design
-
9usability
-
10creativity
-
9content
More by Engineer
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
461 0 0 -
RF Control training board for students based on ESP32 C3
613 0 2 -
Aquarius+ Computer, Standard PCB
820 0 4 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
574 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
499 0 1 -
Nintendo Famicom HVC-001 Controller Shells
596 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
551 0 4 -
COMMODORE 128 15KHz DISPLAY ADAPTER (C128 80 COLUMN ADAPTER)
751 1 5 -