RF Circulator Board
I made this for some circulators I had. One part for a simple surface mount circulator. the other half a two part design to sandwich, the holes don't line up and you will need to add a copper strap on the back for a good ground
RF Circulator Board
Project images are for reference only. Actual production is based on the manufacturing files on the project page.
Please review the designer's notes (e.g., PCB thickness) and select the appropriate options.
PCBWay is not responsible
for issues caused by unsuitable parameter selections.
For more important ordering information, please refer to
Read More
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen（Without Speaker）
BUY NOW
- Comments(0)
- Likes(0)
More by IMSAIGUY
-
Op-amp Test Board
This is a two section board. two dual op-amps can be compared. Half of the device is used in a non-i...
-
Attiny3224 plus OLED and Switches (rev B)
this adds a programming connector, see my other shared project. also added was pin names
-
Attiny3224 plus OLED and Switches
I constantly use an oled display and switches for protoboard experiments. this saves me lots of spac...
-
Photodiode Amplifier with Gain Settings
just a fun project, 4 gain settings transimpedance amp
-
Tiny RS232 Monitor
YouTube videos describe the circuit. The Rev B board fixes the ground problem and correctly connects...
-
Kaypro ROM Selector Board
Here is my video on the project
-
SDK85 8755 EPROM Adapter
A youtube will follow to explainThis is pin compatible with an 8755 chip which is ROM and I/O. This ...
-
7414 Fast Edges
I've done a couple videos on this subject
-
EL2018 EL2252 board for HP 3458A
Here is how it was done by Agilent. Note: the +V is different between the two EL2018. one uses +15 a...
-
Small Gear Motor Housing
This is a 3D print file for a housing/mount for small gear motors. the motor slides into the housing...
-
Panaplex Display Board
this project is documented on YouTube
-
ATTINY ETC board for ETW-3800 Microprocessor Trainer
this board fits the Heathkit ETW-3800 trainer. it has I2C breakout chips to allow lots of IO to conn...
-
Narrow SO-20 to DIP Adapter
this results in a 0.300" DIP for protoboardsit also includes a spot for a bypass capacitor to be use...
-
Narrow SO-16 to DIP Adapter
the DIP has a 0.300" size for protoboard maximization
-
Tiny IMSAI 8080 Computer
This uses an ATTINY814 microcontroller and a bunch of 74595 shift registers to flash the LEDs and re...
-
Narrow SO-14 SMD to DIP Adapter
I made this for using Attiny414 814 type devices on a protoboard with only 0.3" of width
-
Digital Capacitor Bandpass Filter
uses PE64012 serial programmable digital capacitorhttps://youtu.be/zgKv5fhoEHI
-
Mini-Circuits MAR MMIC Amplifier
When ordering board, choose 0.8mm thickness. This is correct thickness for 50ohm transmission line.R...
-
Programmable Mist Maker - XIAO / QT PY Extension
1017 2 1 -
RadioHAT - Raspberry Pi radio development platform
823 0 2 -
-
-
-
-
ARPS-2 – Arduino-Compatible Robot Project Shield for Arduino UNO
3279 0 6 -
A Compact Charging Breakout Board For Waveshare ESP32-C3
3902 3 8 -
AI-driven LoRa & LLM-enabled Kiosk & Food Delivery System
4279 2 2
