Popular: Arduino Automation Commodore Iot Raspberry pi
Projects 2581
Questions 55
Feedback 993
Blog 23
Sponsorships 136
AtTinyDuino
Fernando García Pérez May 20,2019
R1 value is 1 KOhm. The two copper pads on the right are for connecting a 5V battery. The pad that goes to the resistor is for the positive terminal of the battery and the other one for the negative terminal.
DIY arduino AtTiny
1407
0
3
database for pic arduino and arm microntrller
PEREIRA SANTOS May 14,2019
database for pic arduino and arm microntrollercode#include <Wire.h>    #define disk1 0x50    void setup(void){ Serial.begin(9600); Wire.begin();    unsigned int address = 0;  writeEEPROM(disk1, address, 26); Serial.print("Echo from EEPROM 24C02 for adress 0x00: "); Serial.print(readEEPROM(disk1, address), DEC);} void loop(){} void writeEEPROM(int deviceaddress, unsigned int eeaddress, byte d...
data bank
1915
0
1
CeSIO Cervus Shield I/O
Rosas May 09,2019
A pcb with all the I / O of Cervus (compatible with Arduino PCBs), available in connectors accompanied by + V and Gnd, whereby groups we can choose how we feed it: a + 5V, A + 3.3V or external V, giving the possibility to connect elements such as sensors, servos and other devices, has connector for ESP01 and Bluetooth.It allows to use the DD05CVSA module to control a Li-ion battery.
escornabot shield Arduino
2484
1
2
Cervus Arduino Leonardo Coompatible
Rosas May 09,2019
Characteristics of Cervus:- It has a switch on the board.- Power input by 3.5mm terminal block.- Front reset button (accessible with shield).- Voltage selector 5V or 3.3V- 8 open collector Darlington buffers.- Tx / Rx connector for Bluetooth module- Tx / Rx connector for ESP-01 module.- Buzzer (can be disabled by bridge)- Strip of pines D8-D13, GND and Aref. Compatible with Stripboard.- Selectors (plate welding) to connect or disconnect the leds Tx, Rx and L13.
Arduino escornabot steam
3348
2
1
Illuminated Button Matrix
David Johnson-Davies May 09,2019
This is a 4 x 4 matrix of illuminated pushbuttons with a two-wire I2C interface that you can use for games, music, or control applications. The circuit is controlled by an ATtiny88, and you can independently set the state of the lights, or read the buttons, via I2C. I've included a demo program for the Arduino Uno that uses the Button Matrix to play a puzzle game called Tacoyaki.For more information see Illuminated Button Matrix.
I2C Arduino
5457
0
4
Funi Midistik
Kimitobo May 09,2019
FuniFi Midistik is a compact, programmable MIDI controller for synthesisers. There is a popular ATtiny85 microcontroller in the heart of the device which can be progrmmed with Arduino IDE or just sending a wav file of the precompiled code using Audiobootloader. A collection of example patches are available via the Funi-fi Github repository or sending analog voltages via 12Bit DAC and protective OpAmp. The device plugs directly in to MIDI in port (different soldering options for various MIDI port...
Arduino MIDI DIY electronics
3872
0
3
LED controll for rc drone
José Klinsman Jorge May 05,2019
https://www.youtube.com/channel/UCUq6JWtwjapS-7EBCCHpN6w?view_as=subscriber
drone arduino
1574
0
1
IV‐3, IV-3a, IV-6 - VFD shield for Arduino, Clock, Thermometer, Volt Meter (ИВ-6, ИВ-3)
leoloel May 03,2019
VFD Shield for ArduinoSoftwareDocumentation of each sketch can be found in the top of the source.The sketches were developed and tested for various versions of Arduino IDE and required libraries, depending on the period of time they were released. See the documentation in the sketches for more information.When using the serial monitor in the Arduino IDE, make sure the end-of-line and baud rate settings correspond with the documention in the source of the sketch.Direct AccessIV-3 Shield direct ac...
IV‐3 IV-3a IV-6
7922
1
8
SWR and Power meter.
Alexander Antonov May 02,2019
This device is designed to measure the SWR and the current transmitter power.You must use an external sensor.The advantage of this device is that the measurement results can be displayed on the PC screen.More details in the video.
arduino swr swr meter
5755
1
5
2 Channel Relay Module
SUKHJEET DHALIWAL May 01,2019
Two Channel RelayThis module contians two relays that are electrically isolated from the controlling input. The relays can be used to switch higher voltage and current loads than a microcontroller can traditionally accomplish.FeaturesPowered from 5V or 12V2 channelsCan be used as Normally Open (NO) or Normally Closed (NC)
ARDUINO AUTOMATION HOME
3264
2
1
Popular Creator
DAS
Excellent Engineer
Project: 53 Followers: 117
🙂
Excellent Engineer
Project: 86 Followers: 59
Casimiro
Excellent Engineer
Project: 6 Followers: 489
YT
Excellent Engineer
Project: 8 Followers: 14
Cappa
Excellent Engineer
Project: 1 Followers: 0
Popular Project
DIY Active FFB Pedal PCBA
Easy one click ordering of Ghilipert PCAB V2.2 REV BNo solderinghttps://github.com/gilphilbert/DIY-Sim-Racing-FFB-Pedal-PCBsAsk for part 25 : SQP5W-5Ω±5%-9MMore info here :https://youtu.be/PMupeveZSFM...
4G Hacker Phone
Have you always wanted an easier to use and more powerful Flipper Zero?Are you tired of getting detained by the TSA because of your WiFi hat on your Flipper Zero? Then this is the solution for you. It...
SensWear: An Open-Source, Modular, AI-Ready Wearable Platform
SensWear is an open-source, modular wearable development platform that gives researchers, engineers, and makers control over their hardware, firmware, and raw sensor data. It combines a flexible main ...
DIY XBOX Controller
Greetings everyone, and welcome back. Here's something fun and custom.This is my version of an Xbox controller, which I built from scratch. It features an ESP32-C6 DevKit as the main MCU, paired with ...
Programmable Mist Maker - XIAO / QT PY Extension
This is an open source, programmable mist maker built as an expansion board for the Seeed Studio XIAO ESP32-C6. It mounts directly on the XIAO or QT PY, is powered over USB-C, and turns a piezo atomiz...
View More
Hot Project Tags
Space Exploratio Virtual reality Microcontroller DIY Synthesizer Weather Station Synthesizer Antenna TVC