Popular: Arduino Automation Commodore Iot Raspberry pi
Projects 2361
Questions 54
Feedback 956
Blog 23
Sponsorships 117
AtTinyDuino
Fernando García Pérez May 20,2019
R1 value is 1 KOhm. The two copper pads on the right are for connecting a 5V battery. The pad that goes to the resistor is for the positive terminal of the battery and the other one for the negative terminal.
DIY arduino AtTiny
1048
0
3
database for pic arduino and arm microntrller
PEREIRA SANTOS May 14,2019
database for pic arduino and arm microntrollercode#include <Wire.h>    #define disk1 0x50    void setup(void){ Serial.begin(9600); Wire.begin();    unsigned int address = 0;  writeEEPROM(disk1, address, 26); Serial.print("Echo from EEPROM 24C02 for adress 0x00: "); Serial.print(readEEPROM(disk1, address), DEC);} void loop(){} void writeEEPROM(int deviceaddress, unsigned int eeaddress, byte d...
data bank
1475
0
1
CeSIO Cervus Shield I/O
Rosas May 09,2019
A pcb with all the I / O of Cervus (compatible with Arduino PCBs), available in connectors accompanied by + V and Gnd, whereby groups we can choose how we feed it: a + 5V, A + 3.3V or external V, giving the possibility to connect elements such as sensors, servos and other devices, has connector for ESP01 and Bluetooth.It allows to use the DD05CVSA module to control a Li-ion battery.
escornabot shield Arduino
1987
1
2
Cervus Arduino Leonardo Coompatible
Rosas May 09,2019
Characteristics of Cervus:- It has a switch on the board.- Power input by 3.5mm terminal block.- Front reset button (accessible with shield).- Voltage selector 5V or 3.3V- 8 open collector Darlington buffers.- Tx / Rx connector for Bluetooth module- Tx / Rx connector for ESP-01 module.- Buzzer (can be disabled by bridge)- Strip of pines D8-D13, GND and Aref. Compatible with Stripboard.- Selectors (plate welding) to connect or disconnect the leds Tx, Rx and L13.
Arduino escornabot steam
2797
2
1
Illuminated Button Matrix
David Johnson-Davies May 09,2019
This is a 4 x 4 matrix of illuminated pushbuttons with a two-wire I2C interface that you can use for games, music, or control applications. The circuit is controlled by an ATtiny88, and you can independently set the state of the lights, or read the buttons, via I2C. I've included a demo program for the Arduino Uno that uses the Button Matrix to play a puzzle game called Tacoyaki.For more information see Illuminated Button Matrix.
I2C Arduino
4604
0
4
Funi Midistik
Kimitobo May 09,2019
FuniFi Midistik is a compact, programmable MIDI controller for synthesisers. There is a popular ATtiny85 microcontroller in the heart of the device which can be progrmmed with Arduino IDE or just sending a wav file of the precompiled code using Audiobootloader. A collection of example patches are available via the Funi-fi Github repository or sending analog voltages via 12Bit DAC and protective OpAmp. The device plugs directly in to MIDI in port (different soldering options for various MIDI port...
Arduino MIDI DIY electronics
3304
0
3
LED controll for rc drone
José Klinsman Jorge May 05,2019
https://www.youtube.com/channel/UCUq6JWtwjapS-7EBCCHpN6w?view_as=subscriber
drone arduino
1254
0
1
IV‐3, IV-3a, IV-6 - VFD shield for Arduino, Clock, Thermometer, Volt Meter (ИВ-6, ИВ-3)
leoloel May 03,2019
VFD Shield for ArduinoSoftwareDocumentation of each sketch can be found in the top of the source.The sketches were developed and tested for various versions of Arduino IDE and required libraries, depending on the period of time they were released. See the documentation in the sketches for more information.When using the serial monitor in the Arduino IDE, make sure the end-of-line and baud rate settings correspond with the documention in the source of the sketch.Direct AccessIV-3 Shield direct ac...
IV‐3 IV-3a IV-6
6622
1
8
SWR and Power meter.
Alexander Antonov May 02,2019
This device is designed to measure the SWR and the current transmitter power.You must use an external sensor.The advantage of this device is that the measurement results can be displayed on the PC screen.More details in the video.
arduino swr swr meter
5005
1
5
2 Channel Relay Module
SUKHJEET DHALIWAL May 01,2019
Two Channel RelayThis module contians two relays that are electrically isolated from the controlling input. The relays can be used to switch higher voltage and current loads than a microcontroller can traditionally accomplish.FeaturesPowered from 5V or 12V2 channelsCan be used as Normally Open (NO) or Normally Closed (NC)
ARDUINO AUTOMATION HOME
2505
2
1
Popular Creator
jjaime68
Excellent Engineer
Project: 1 Followers: 4
König
Excellent Engineer
Project: 5 Followers: 109
Casimiro
Excellent Engineer
Project: 6 Followers: 465
Prof
Excellent Engineer
Project: 2 Followers: 0
Sahu
Excellent Engineer
Project: 1 Followers: 0
Popular Project
A Modified zFlip 5
With many Samsung zFlip phones hitting the unfortunate fate of a broken folding screen, I took it as an opportunity to build my own silly phone. Taking only the minimum parts required for the phone to...
ESP32-BlueJammer
The ESP32-BlueJammer (Bluetooth jammer, BLE jammer, WiFi jammer, RC jammer) disrupts various devices using an ESP32 and nRF24 modules, causing plenty of noise and sending unnecessary packets (DoS).It ...
Air Quality Monitor
The Air Quality Monitor is a compact, ESP32-C3–based device designed to track and display key indoor environmental metrics in real time. At its core, it integrates the Sensirion SEN54 for particulate ...
Flipper Zero Dev Board: BW16 RTL8720DN 2.4 GHz & 5 GHz Deauther
Upgrade your Flipper Zero with the AI Thinker BW16 RTL8720DN Dual-Band WiFi Expansion Board. Enhance your device's connectivity capabilities with support for both 2.4 GHz and 5 GHz WiFi bands. Perfect...
🔋 How to Make a Power Bank Module at Home
Are you looking to build your own DIY power bank at home? In this blog post, we’ll show you how to create a powerful and efficient power bank module using commonly available components like the TP4056...
View More
Hot Project Tags
Space Exploratio Virtual reality Microcontroller DIY Synthesizer Weather Station Synthesizer Antenna TVC