Popular: Arduino Automation Commodore Iot Raspberry pi
Projects 2516
Questions 55
Feedback 981
Blog 23
Sponsorships 127
One Channel Relay Module for Arduino
Fahad Nov 21,2020
This is a one-channel relay module based on the 12vdc SPDT type relay. This relay module can be used with Arduino boards and also with other controller boards. Watch this relay module in action. Article Link:https://www.electroniclinic.com/tof10120-laser-rangefinder-arduino-display-interfacing-code/https://www.electroniclinic.com/tof10120-laser-rangefinder-arduino-display-interfacing-code/
relay module arduino relay module one channel relay module
4425
0
1
KEBUN DIGITAL
Arsana Nov 21,2020
Untuk tata letak komponen akan di update secepatnya atau langsung hubungi admin di nomor yang ada pada keterangan video untuk mendapatkan tata letak komponen nya.
iot ARDUINO
4038
1
3
Arduino Nano Granular OSC
Doğan ŞEŞEOĞULLARI Nov 20,2020
This pcb design project is based on Peter Knight's Arduino Nano Synth code and Notes and Volts Line Output upgrade. You can find all components needed in Schematic and .xls file. It has 2 option to power the device. All components are DIP type of component. Please use ceramik type 33 nF capasitor.The circuit can be power up by directly arduino usb socket or power adaptor socket by using a 9v adaptor. Please pay attention if your adaptors pinout should be right this; TIP : (-)...
synth oscillator granular
7129
0
4
Fire Alarm System with Arduino Nano
🙂 Nov 20,2020
Hello!This is a simple project made with Arduino Nano and some common modules. I used an infrared flame sensor, an MQ-2 smoke / gas sensor, an audible warning buzzer, a relay that could control a sprinkler, a digital display and an On / Off button. As many modules are used for this project, I did not pay too much attention to the positioning of the parts, jump wires are needed.Note: Pay attention to the polarities, and to the positioning of the flame sensor, normally short leg is connected to a ...
flame smoke flame sensor
1999
0
2
USB to UART Converter module
Emb-dev Nov 19,2020
This is the pcb design file for USB to Serial converter. In this design i have used CH340 USB to serial converter IC which is very cheap and easily available.This tool is must tools while doing embedded development.
usb to uart ft232 ch340
2772
0
6
sduino UNO
Roy Nov 19,2020
The sduino UNO is an attempt at creating a mechanically and electrically Arduino-UNO-compatible development board based on the STM8S105K6 microcontroller. Both mechanical and electrical design are to a notable degree based on the Arduino UNO board.Source files here: https://github.com/roybaer/sduino_unoDifferencesThe following paragraphs highlight the most important differences between Arduino UNO and sduino UNO.MechanicalThe gap between the upper socket strips has been reduced from 0.06 to 0.05...
development board creative commons arduino
3592
0
1
uSDX HF Transceiver - Serial Resonance 3 Band Module
Alexiev Nov 19,2020
uSDX now goes multi band multiband capability on my V1.02 PCB uSDX HF TransceiverAll credits to BARBAROS ASUROGLU , check his site for components for each band and more info !!you need the transceiver PCBSerial Resonance LPF Tri Band Module" Band dependent components list in the attached documentPlease visit the author page for more info! The band dependent capacitor and toroid turn values can be grabbed from the relevant table below.RF IN switch and ANT switch has 3 positions marked as 1, ...
uSDX SSB transciever
4742
0
5
Mini Game Console
Nov 19,2020
Game console that works with Attiny85 chip and oled screen 128x64.
oled attiny85 arduino
5879
1
6
Lite3DP S1: MSLA 3D Printer, Arduino Based and Open Source (v0.1)
Bonini Nov 18,2020
Lite3DP S1 is a resin micro 3D printer with MSLA technology, the first of its kind based entirely on an Arduino board. It will be provided in a complete and easy-to-assemble kit format, offering an enriching and educative experience for its users.The Lite3DP is a 3D printer that stands out for its simplicity, absence of noise, and being small, lightweight, and low cost. With the RepRap project as inspiration, it seeks to set a milestone within resin 3D printing: popularize simple and inexpe...
Lite3DP LCD-SLA MSLA 3D printer
12372
11
16
WiFi based AC dimmer using Nodemcu
Nov 18,2020
This pcb layout is for the AC dimmer using esp8266. This project is WIFI based AC dimmer where we can control the power provides to the appliances.How it works:We are using Zero cross detector to detect the zero cross for AC power line. Once we detect the zero cross using Zero cross detector then turn ON the triac for required time.Following are the materials used for this projectcl - CPl : Capacitor_THT:CP_Radial_DS.0mm_P2.50mmc2 - C : Capacitor_THT:C_Disc_D3.0mm_W2.0mm_P2.50mmc3 - CPl : Capaci...
arduino home automation ac dimmer
3280
0
4
Popular Creator
Green Energy
Excellent Engineer
Project: 24 Followers: 446
jjaime68
Excellent Engineer
Project: 1 Followers: 4
König
Excellent Engineer
Project: 5 Followers: 109
Casimiro
Excellent Engineer
Project: 6 Followers: 486
Guidolin
Excellent Engineer
Project: 14 Followers: 36
Popular Project
AERIS-10 Open Source Phased Array Radar
The AERIS-10 is a low‑cost open‑source phased‑array radar platform designed for makers, researchers and educators. Operating around 10.5 GHz, the system can detect and track multiple objects at ranges...
4G Hacker Phone
Have you always wanted an easier to use and more powerful Flipper Zero?Are you tired of getting detained by the TSA because of your WiFi hat on your Flipper Zero? Then this is the solution for you. It...
Project Aura AQ Sensor Hub PCB v1.1
This is the custom PCB for Project Aura AQ, an open-source ESP32-S3 air-quality monitor with touchscreen UI, local web dashboard, MQTT, and Home Assistant support.What is included on the PCB:- Built-i...
Simple lo-fi offline MP3 player for the Zion Brock vintage radio (official PCB)
Offline | Mono | Lo-FiThe PCB version of the Vintage Radio does not receive live radio signals. It is a self-contained offline music player. You load albums or tracks onto a microSD card, insert ...
DIY Active FFB Pedal PCBA
Easy one click ordering of Ghilipert PCAB V2.2 REV BNo solderinghttps://github.com/gilphilbert/DIY-Sim-Racing-FFB-Pedal-PCBsAsk for part 25 : SQP5W-5Ω±5%-9MMore info here :https://youtu.be/PMupeveZSFM...
View More
Hot Project Tags
Space Exploratio Virtual reality Microcontroller DIY Synthesizer Weather Station Synthesizer Antenna TVC