Product Description

PCBWay TP4056 1A Lithium Battery Charging Module

Product Features:

  • Charging Protection: Prevents battery overcharging and over-discharging, with automatic control of charging current for enhanced battery protection.
  • Type-C Female Interface: Features a Type-C receptacle for convenient DIY applications, preserving input voltage soldering points.


Product Specifications:

  • Input Voltage: 4.5V-5V
  • Maximum Charging Current: 1000mA
  • Charging Cut-off Voltage: 4.2V±1%
  • Battery Over-Discharge Protection Voltage: 2.5V/3A
  • Board Dimensions: 2.8cm*1.7cm


Usage Instructions:

Connect the Type-C receptacle and the adjacent + and - solder pads as the power input. Supply 5V input voltage. Connect B+ to the positive terminal of the lithium battery and B- to the negative terminal. Connect OUT+ and OUT- to the load, such as a boost module. Once the battery is connected to B+ and B-, plug in a mobile phone charger to the USB port. The blue light will illuminate, indicating the power source is connected, and the red light will flash, indicating charging is in progress. After charging is complete, the red light will stop flashing and remain steady.

You can connect a load to OUT+ and OUT-, and the red light will stay on continuously. When there is a power source connected to the input, the current is supplied from the power source. If there is no input power, the current is drawn from the battery. The output is automatically turned off if the battery voltage drops below 2.5V.


NOTE:

During the initial connection to the battery, there may be no voltage output at the OUT terminal. In this case, it is necessary to supply 5V to the power input terminal for a brief charge to activate the protection circuit. When using a mobile phone charger as the power source, it is essential to ensure an output of at least 1A; otherwise, normal charging may not be possible.

  • Comments(0)
You can only upload 1 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000

    You might like

    • PCBWay TP4056 1A Lithium Battery Charging Module
      $1.00 or 120 Beans
      Redeem Now
    • -50%
      PCBWay Single-Channel Relay Module with Delayed Power-off, Triggered Delay, and Cyclical Timing Circuit Switch
      $0.99 or 120 Beans
      Redeem Now
    • 5.5V/80mA Solar Panel DIY Solar
      $2.00 or 240 Beans
      Redeem Now
    • -50%
      Good Quality Breadboard Power Supply Module
      $0.99 or 240 Beans
      Redeem Now
    • Four Way Holder V3 Development Board(Compatible with Raspberry Pi/STM32)
      $8.99 or 1080 Beans
      Redeem Now
    • -50%
      1 Channel Relay Module 5V with optocoupler Support High and Low Level Trigger
      $0.99 or 120 Beans
      Redeem Now
    • -50%
      NE555 Frequency Adjustable Pulse Generator Module
      $0.99 or 120 Beans
      Redeem Now
    • Relay Module Interface Boards for Arduino Low Level Trigger 5V 2 Channels
      $2.00 or 200 Beans
      Redeem Now
    • XL6009 DC-DC Adjustable Stet-up Power Converter Module
      $2.00 or 200 Beans
      Redeem Now
    • LM2596S DC-DC 3A Buck Adjustable Step-down Power Supply Converter Module
      $0.99 or 120 Beans
      Redeem Now
    • L298N PWM Stepper Motor Drive Controller Board Module
      $5.00 or 500 Beans
      Redeem Now
    • TP4056 5V Mini USB 1A Lithium Battery Charger Module
      $1.00 or 100 Beans
      Redeem Now
    • MB102 Breadboard Power Supply Module 3.3V/5V
      $1.00 or 100 Beans
      Redeem Now
    • MP1584 3A DC to DC Step Down Converter Buck Module Fixed Output 3.3V
      $1.00 or 100 Beans
      Redeem Now
    • Step-Down & Step-Up Converter DC-DC 1.8V-5V 3V 3.7V to 3.3V Power Module
      $1.00 or 100 Beans
      Redeem Now
    • Bread Board 3.3/5V Power Supply Module
      $3.99 or 480 Beans
      Redeem Now
    Product Name
    Link for reference
    Quantity