Popular: Arduino Automation Commodore Iot Raspberry pi
Projects 2516
Questions 55
Feedback 981
Blog 23
Sponsorships 127
Spinning display POV
Diaz Sep 15,2018
### DESCRIPTIONThis is a spinning display with Arduino and TLC5940, show a message with 16 LEDs### TECHNICAL DETAILS / COMPONENTSAll the info and a video is in http://www.catykanal.com### LEARN / TOPIC / BUILD INSTRUCTIONS
Arduino LEDs Display
2936
0
0
ESP8266-01 Programmer easy connection
Lautaro Tourn Sep 15,2018
With this PCB you can easily flash your ESP8266-01 withoout adding wires or complicated connections to breadboard.You just plug your USB-TTL converter (CP2102 or PL2303), select the mode (flash or normal), click reset and go.The only components you need are the push-button por reset and the interruptor for mode select (this puts GPIO0 to GND or 3,3V.
PCB Design Contest SpainLabs Yoreparo
2609
1
2
SDR Transceiver 10-160 meter band
YE3CIF.COM Sep 14,2018
This SDR was designed from some of my experiments so far, from various sources with improvements here and there so that I can get maximum results.LO using Si5351A which is controlled by Arduino Nano produces a frequency that is wide enough Max 160Mhz, of course allows us to make Exciter up to 10M band. LO = work freq x 4.My BPF takes from the us5ncj design using an already-built Inductor, so it is practical without the need to roll.Parts of TX, RX, and RF Preamp are not much different from the S...
radio si5351 ssb
27322
5
42
Arduino acceleration logger
Kristoffer Sl?ttsveen Sep 11,2018
### DESCRIPTIONCurrently, this design has some faults! the 3k6Ohm resistor should be a 2k4Ohm in stead. The 5V regulator pinout is wrong compared to the footprint shown on the board. The Arduino MKRZERO footprint is 2.54mm too wide. ### TECHNICAL DETAILS / COMPONENTS### LEARN / TOPIC / BUILD INSTRUCTIONS
SD card battery powered datalogger
1529
0
0
DroneMesh FPV Drone Finder V1
DroneMesh Sep 10,2018
### DESCRIPTIONThis is a FPV Drone Finder that will help you locate your quadcopter from its 5.8ghz VTX Rssi.### The Codehttps://gist.github.com/dronemesh/5ffe065e090be75bc0ed61fea99952e9### BUILD VIDEOhttps://youtu.be/KeVwsTaWcHg### COMPONENTSSkyzone RX5803 12https://www.banggood.com/Skyzone-RX5803-5_8GHz-48CH-Raceband-AV-FM-Receiver-Module-p-1159848.html?p=CS101558118042016088&utm_content=huangguocan&utm_campaign=mesh.droneOled displayhttps://www.banggood.com/1_3-Inch-4Pin-Blue-OLED-12...
2nd PCB design Contest 5.8ghz SMA
6924
1
4
Inteligent electronic load using ST-Nucleo-L432KC
Tadeáš Pilař Sep 07,2018
My goal is to create simple electronic load. Requirements are 2 chanels, power monitoring, constant voltage mode, constant current mode, constant power mode. The device should also be able to discharge batteries, monitor power drained and stop discharging when threshold voltage is reached. Each channel should be able to handle 5 amps with possibility for future upgrade.As the brain of this device was choosen ST-Nucleo-L432KC development board. Its 2 DACs will be used to drive power transist...
ATMakers Yoreparo SpainLabs
2751
1
3
Pro-A-WiFi01-Shield
Jesus Villarroel Aug 30,2018
### DESCRIPTIONThis is an Arduino UNO shield which was designed to ease the flashing process of the ESP01 module. When I started programming this module, the process was sort of messy and complicated. Required a lot of wire jumpers along the breadboard, the ESP01, and the Arduino UNO. Using this shield, it will require just placing some jumpers to flash the WiFi module.Moreover, this shield can be used to connect the Arduino UNO to the cloud through the ESP01 using AT commands. ##...
Arduino Shield ESP01 IoT
1682
0
3
nRF24l01+ Joystick Remote Control
Taylor Amarotico Aug 24,2018
### DESCRIPTIONI designed this because I wanted a compact remote control so I could easily control my tracked vehicle I designed. It utilizes a nRF24l01+, an Atmega328p, and a joystick to make a simple circuit that does not require a ton of components. It also has a bootloader header, and a programming header so you can quickly and easily flash a bootloader to the Atmega328p, and then easily program with only a few connectors. It has a 5v power regulator for the Atmega328p as well as a 3.3v powe...
arduino atmega328p remote control
2661
0
4
8 LEDS PANEL INDICATOR
Eduardo Aug 23,2018
8 LED PANEL INDICATOR.
module arduino pic
2992
0
5
4 DIGITS LED DISPLAY
Eduardo Aug 23,2018
4 DIGITS LED DISPLAY
led arduino pic
2160
0
2
Popular Creator
Green Energy
Excellent Engineer
Project: 24 Followers: 446
jjaime68
Excellent Engineer
Project: 1 Followers: 4
König
Excellent Engineer
Project: 5 Followers: 109
Casimiro
Excellent Engineer
Project: 6 Followers: 486
Guidolin
Excellent Engineer
Project: 14 Followers: 36
Popular Project
AERIS-10 Open Source Phased Array Radar
The AERIS-10 is a low‑cost open‑source phased‑array radar platform designed for makers, researchers and educators. Operating around 10.5 GHz, the system can detect and track multiple objects at ranges...
4G Hacker Phone
Have you always wanted an easier to use and more powerful Flipper Zero?Are you tired of getting detained by the TSA because of your WiFi hat on your Flipper Zero? Then this is the solution for you. It...
Project Aura AQ Sensor Hub PCB v1.1
This is the custom PCB for Project Aura AQ, an open-source ESP32-S3 air-quality monitor with touchscreen UI, local web dashboard, MQTT, and Home Assistant support.What is included on the PCB:- Built-i...
Simple lo-fi offline MP3 player for the Zion Brock vintage radio (official PCB)
Offline | Mono | Lo-FiThe PCB version of the Vintage Radio does not receive live radio signals. It is a self-contained offline music player. You load albums or tracks onto a microSD card, insert ...
DIY Active FFB Pedal PCBA
Easy one click ordering of Ghilipert PCAB V2.2 REV BNo solderinghttps://github.com/gilphilbert/DIY-Sim-Racing-FFB-Pedal-PCBsAsk for part 25 : SQP5W-5Ω±5%-9MMore info here :https://youtu.be/PMupeveZSFM...
View More
Hot Project Tags
Space Exploratio Virtual reality Microcontroller DIY Synthesizer Weather Station Synthesizer Antenna TVC