Popular: Arduino Automation Commodore Iot Raspberry pi
Projects 2580
Questions 55
Feedback 993
Blog 23
Sponsorships 136
A Digital FM Receiver with Arduino
PCBWay Team Nov 23,2020
FM transmitters/receivers are among the top favorite circuits of any electronic enthusiast. In this article/video, I have introduced a complete digital FM receiver design that has equipped with an LCD screen and three push-buttons. It can search for the FM signals from 76MHz to 108MHz manually and automatically (Scan mode). The signal strength is also displayed as a bar graph on the LCD screen. The output sound is amplified by a 3W+3W Class-D stereo amplifier that handles high-quality and strong...
arduino
11838
3
17
MicroController Training Set
BERBER Nov 22,2020
It was designed as a development board for young developers.And it is designed for high school and middle school students to learn to code. it has many sensors on it. They have a five led, rgb led, two button,buzzer, remote control, ldr, ntc, temperature and humidity sensor, lcd, bluetooth, motor shield, ultrasonic sensor and arduino nano. This card, which contains many sensors and will be free for our students. And will be able to code with any program they want.(Arduino IDE,Scratch,MBlock etc....
arduino micro controller education
5415
12
14
8 button controller shield for Arduino UNO
Robot Nov 21,2020
Build controller for UNO with buttons that connect to ground when closed. Buttons are Panasonic EVQ-11D05B, which is Digikey part number P15931SCT.
controller buttons shield
1977
0
0
3 stepper motor controller carrier sheild for Arduino UNO compatible boards
Robot Nov 21,2020
This is the simplest possible way I could come up with to control 3 stepper motors with an Arduino. The board has no active components, it just connects the Arduino board to the MP6500 carrier boards sold from Pololu and other places. Labels in silk screen show how pins map to pins.
mp6500 robotics stepper motor
2016
0
1
One Channel Relay Module for Arduino
Fahad Nov 21,2020
This is a one-channel relay module based on the 12vdc SPDT type relay. This relay module can be used with Arduino boards and also with other controller boards. Watch this relay module in action. Article Link:https://www.electroniclinic.com/tof10120-laser-rangefinder-arduino-display-interfacing-code/https://www.electroniclinic.com/tof10120-laser-rangefinder-arduino-display-interfacing-code/
relay module arduino relay module one channel relay module
4742
0
1
KEBUN DIGITAL
Arsana Nov 21,2020
Untuk tata letak komponen akan di update secepatnya atau langsung hubungi admin di nomor yang ada pada keterangan video untuk mendapatkan tata letak komponen nya.
iot ARDUINO
4218
1
3
Arduino Nano Granular OSC
Doğan ŞEŞEOĞULLARI Nov 20,2020
This pcb design project is based on Peter Knight's Arduino Nano Synth code and Notes and Volts Line Output upgrade. You can find all components needed in Schematic and .xls file. It has 2 option to power the device. All components are DIP type of component. Please use ceramik type 33 nF capasitor.The circuit can be power up by directly arduino usb socket or power adaptor socket by using a 9v adaptor. Please pay attention if your adaptors pinout should be right this; TIP : (-)...
synth oscillator granular
7306
0
4
Fire Alarm System with Arduino Nano
🙂 Nov 20,2020
Hello!This is a simple project made with Arduino Nano and some common modules. I used an infrared flame sensor, an MQ-2 smoke / gas sensor, an audible warning buzzer, a relay that could control a sprinkler, a digital display and an On / Off button. As many modules are used for this project, I did not pay too much attention to the positioning of the parts, jump wires are needed.Note: Pay attention to the polarities, and to the positioning of the flame sensor, normally short leg is connected to a ...
flame smoke flame sensor
2133
0
2
USB to UART Converter module
Emb-dev Nov 19,2020
This is the pcb design file for USB to Serial converter. In this design i have used CH340 USB to serial converter IC which is very cheap and easily available.This tool is must tools while doing embedded development.
usb to uart ft232 ch340
2931
0
6
sduino UNO
Roy Nov 19,2020
The sduino UNO is an attempt at creating a mechanically and electrically Arduino-UNO-compatible development board based on the STM8S105K6 microcontroller. Both mechanical and electrical design are to a notable degree based on the Arduino UNO board.Source files here: https://github.com/roybaer/sduino_unoDifferencesThe following paragraphs highlight the most important differences between Arduino UNO and sduino UNO.MechanicalThe gap between the upper socket strips has been reduced from 0.06 to 0.05...
development board creative commons arduino
3783
0
1
Popular Creator
Jason
Excellent Engineer
Project: 10 Followers: 4
König
Excellent Engineer
Project: 5 Followers: 112
Casimiro
Excellent Engineer
Project: 6 Followers: 489
YT
Excellent Engineer
Project: 8 Followers: 14
Cappa
Excellent Engineer
Project: 1 Followers: 0
Popular Project
DIY Active FFB Pedal PCBA
Easy one click ordering of Ghilipert PCAB V2.2 REV BNo solderinghttps://github.com/gilphilbert/DIY-Sim-Racing-FFB-Pedal-PCBsAsk for part 25 : SQP5W-5Ω±5%-9MMore info here :https://youtu.be/PMupeveZSFM...
4G Hacker Phone
Have you always wanted an easier to use and more powerful Flipper Zero?Are you tired of getting detained by the TSA because of your WiFi hat on your Flipper Zero? Then this is the solution for you. It...
SensWear: An Open-Source, Modular, AI-Ready Wearable Platform
SensWear is an open-source, modular wearable development platform that gives researchers, engineers, and makers control over their hardware, firmware, and raw sensor data. It combines a flexible main ...
DIY XBOX Controller
Greetings everyone, and welcome back. Here's something fun and custom.This is my version of an Xbox controller, which I built from scratch. It features an ESP32-C6 DevKit as the main MCU, paired with ...
Programmable Mist Maker - XIAO / QT PY Extension
This is an open source, programmable mist maker built as an expansion board for the Seeed Studio XIAO ESP32-C6. It mounts directly on the XIAO or QT PY, is powered over USB-C, and turns a piezo atomiz...
View More
Hot Project Tags
Space Exploratio Virtual reality Microcontroller DIY Synthesizer Weather Station Synthesizer Antenna TVC