Oleg Oleg
RUSSIAN FEDERATION, THE • + Follow
Edit Project
Description
MICROCONTROLLER BASED RUNNING LIGHT CONTROLLER
This project provides some lighting effect by the blinking pattern of the bulbs connected at its output.
Up to 8 Bulbs can be connected in between connector CN2 to CN9 and AC power to control them should be connected at Connector CN10. DC Power should be applied at Connector CN11 in accordance with the polarity marked on this connector.
Care should be taken while using this it as it contains Main Power on the board.
We can change the Blink pattern by the press of the SET switch and change the blinking speed by the press of the UP and DOWN keys on the PCB.
Fuse F1 will protect the Kit from any possible short circuit and excess current flowing through it.
Microcontroller based design for greater flexibility and ease of control
Triac based switching of loads connected to the circuit
Industry standard isolation with the help of Opto enabled Triac Control
Fuse protection for AC output
SUPPLY 9-12V DC & 230V AC
LOAD-100W max on each output
Simple and easy to use 3 tactile switch enabled control of the project
PBT type connector for connecting supply (AC/DC) and TRIAC output on the PCB
Onboard regulator for regulated supply to the project
Diode protection for reverse polarity connection of DC supply to the PCB
Four mounting holes of 3.2 mm each
PCB dimensions 86 mm x 173 mm
Jun 02,2020
863 views
MICROCONTROLLER BASED RUNNING LIGHT CONTROLLER
863
1
0
Published: Jun 02,2020
Download Gerber file 15
BOM(Bill of materials)
Purchase
Donation Received ($)
PCBWay Donate 10% cost To Author
Only PCB
PCB+Assembly
*PCBWay community is a shared platform and we are not responsible for any design issues.
Copy this HTML into your page to embed a link to order this shared project
Copy
Under the
Attribution-ShareAlike (CC BY-SA)
License.
- Comments(0)
- Likes(1)
You can only upload 1 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
Remove
It looks like you have not written anything. Please add a comment and try again.
View More
- Jernej Chuchek Jul 17,2021
View More
VOTING
0 votes
- 0 USER VOTES
0.00
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Design
1/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Usability
2/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Creativity
3/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Content
4/4
More by Oleg Oleg
- Development Board STM32F103RET6 Development Board Series STM32F103RET6Resources on the board3.3/5.0/12V power input/output pinReset ...
- DAPLINK and STM32 minimum system combination DAPLINK and STM32 minimum system combination, one data cable can complete the download and debugging...
- USB to RS232 This is a program verification board. The main verification content is the function of USB to RS232 ...
- ESP Air Burner The ESP downloader with Air Burnner interface uses probes instead of DuPont cables.
- Docking station USB3.1 Using GL3520 USB 3.1 HUB chip,Supports super high speed, high speed and full speed USB connection, f...
- RX5808 open source receiver 5.8g open source receiver, can receive 5.8g signal, AV video signal output. Rx5808 dual-reception fu...
- 5.8G image transmission module It can be used for AV signal audio and video wireless transmission; baby monitor; wireless camera se...
- GRBL-ESP32 esp32s 3d is suitable for GRBL and marlin software
- STM32 Sensor Node A Small STM32F103C8T6 board with all functional pins exposed. Similar to the BluePill Board except:N...
- 2.8 inch TFT touch screen The module uses a 2.8-inch TFT color LCD screen. The module is compatible with punctual atomic 2.8TF...
- LED dot matrix clock LED dot matrix electronic clock based on 51 single chip microcomputer.Based on STC15W4K series ultra...
- STM32F411Cx 401Cx minimum system + J-LINK debugger The STM32F411 / 401 microcontroller belongs to the STM32 Dynamic Efficiency series. These devices ar...
- Small passive DC constant current electronic load IntroductionA small passive DC adjustable constant current (CC) electronic load with temperature-con...
- Small jlinkV9 downloader V1.0 Adopt typec interface, stm32f205 master control, lead SWD, SWO, support virtual serial port, resista...
- IP2325 dual string lithium battery charging module Miniature charger for dual lithium batteries.Since the IP2325 does not have a charge balancing funct...
- Electronic switch The operating voltage is within 30V. Depends on the PMOS voltage.
- Power supply module NAE20S08 Is based on SY8288A / JW5068A series power supply ic Volume: 10x10x6mm Input range: 4-23vin Output: ...
- Solder paste dispenser A portable miniature intelligent electric SMT solder paste dispensing pen supports quantitative extr...
You may also like
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
307 0 0 -
RF Control training board for students based on ESP32 C3
429 0 2 -
Aquarius+ Computer, Standard PCB
617 0 3 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
457 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
402 0 0 -
Nintendo Famicom HVC-001 Controller Shells
498 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
480 0 4 -
COMMODORE 128 15KHz DISPLAY ADAPTER (C128 80 COLUMN ADAPTER)
585 1 4 -