Geiger counter with touch screen
I heard that electronic enthusiasts will make a Geiger counter.
Facing the increasingly complex world environment and electronic waste,
I will also imitate it.
The foreigner version looks like this more advanced one, with its own parameter calibration and WIFI remote check meter.
In particular, the boost circuit cleverly uses the 555 circuit, which greatly reduces the production cost.
The original post used the Wemos D1 mini board module and I directly integrated it into a board.
This Geiger counter software has two versions, GC-01 and GC-20.
I have packaged GC-01 into an ARDUINO library and can be directly compiled and uploaded with Arduino, or I can use the compiled firmware to upload directly with the ESP8266 download tool.
For the internal structure during production, I used 18650 so the shell is a bit thicker.
Geiger counter with touch screen
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(4)
- Likes(5)
- Trond Even Evensen Mar 06,2024
- Engineer Mar 21,2023
- Simon Wiesner Jun 24,2022
- Engineer Mar 15,2022
- Dusan Chlpek Mar 15,2022
- 2 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
-
8design
-
1usability
-
1creativity
-
1content
-
10design
-
10usability
-
10creativity
-
10content
More by Oleg Oleg
- Development Board STM32F103RET6 Development Board Series STM32F103RET6Resources on the board3.3/5.0/12V power input/output pinReset ...
- DAPLINK and STM32 minimum system combination DAPLINK and STM32 minimum system combination, one data cable can complete the download and debugging...
- USB to RS232 This is a program verification board. The main verification content is the function of USB to RS232 ...
- ESP Air Burner The ESP downloader with Air Burnner interface uses probes instead of DuPont cables.
- Docking station USB3.1 Using GL3520 USB 3.1 HUB chip,Supports super high speed, high speed and full speed USB connection, f...
- RX5808 open source receiver 5.8g open source receiver, can receive 5.8g signal, AV video signal output. Rx5808 dual-reception fu...
- 5.8G image transmission module It can be used for AV signal audio and video wireless transmission; baby monitor; wireless camera se...
- GRBL-ESP32 esp32s 3d is suitable for GRBL and marlin software
- STM32 Sensor Node A Small STM32F103C8T6 board with all functional pins exposed. Similar to the BluePill Board except:N...
- 2.8 inch TFT touch screen The module uses a 2.8-inch TFT color LCD screen. The module is compatible with punctual atomic 2.8TF...
- LED dot matrix clock LED dot matrix electronic clock based on 51 single chip microcomputer.Based on STC15W4K series ultra...
- STM32F411Cx 401Cx minimum system + J-LINK debugger The STM32F411 / 401 microcontroller belongs to the STM32 Dynamic Efficiency series. These devices ar...
- Small passive DC constant current electronic load IntroductionA small passive DC adjustable constant current (CC) electronic load with temperature-con...
- Small jlinkV9 downloader V1.0 Adopt typec interface, stm32f205 master control, lead SWD, SWO, support virtual serial port, resista...
- IP2325 dual string lithium battery charging module Miniature charger for dual lithium batteries.Since the IP2325 does not have a charge balancing funct...
- Electronic switch The operating voltage is within 30V. Depends on the PMOS voltage.
- Power supply module NAE20S08 Is based on SY8288A / JW5068A series power supply ic Volume: 10x10x6mm Input range: 4-23vin Output: ...
- Solder paste dispenser A portable miniature intelligent electric SMT solder paste dispensing pen supports quantitative extr...
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
481 0 0 -
RF Control training board for students based on ESP32 C3
641 0 2 -
Aquarius+ Computer, Standard PCB
851 0 4 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
589 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
511 0 1 -
Nintendo Famicom HVC-001 Controller Shells
612 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
568 0 4 -
COMMODORE 128 15KHz DISPLAY ADAPTER (C128 80 COLUMN ADAPTER)
774 1 5 -