Flip-Flop Circuit
FLIP-FLOP
There are electronic elements whose outputs are stable in two ways with the signal applied to the flip flop circuit inputs. Multivibrators that can maintain the state and, accordingly, the value at one of its outputs continuously when an operating voltage is applied to the circuit are called flip flop circuits. They are elements with different output values in response to variable input voltages, which also contain logic gates in their structure.
The instantaneous change of flip flop circuits is called triggering. It has a total of two stable states, SET (1) and Reset (0). These circuit elements remain in one of the two steady states. For this reason, flip flop circuits are used as storage elements. They maintain their output status as long as the signal applied to their input is not changed, and they can also store 1-bit information.
How Does a Flip Flop Circuit Work?
The circuit is formed by the capacitors filling up and giving voltage in the opposite direction and cutting the connection of these leds with GND by giving reverse voltage to the base of the NPN transistors, which are normally working at saturation, that is, active. The flashing times of the LEDs in this circuit are related to the capacitors. If you then use higher Farad capacitors, generally the flashing time will be longer. The LEDs do not light when there is no voltage to turn the transistors on. In addition, capacitors are normally empty.
Flip-Flop Circuit
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(1)
- (DIY) C64iSTANBUL Jul 03,2023
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Beytullah Gültepe
- Schematic 6 Stage Led Chaser Using Transistor Schematic 6 Stage Led Chaser Using TransistorSchematic 6 Stage Led Chaser Using Transistor Thanks to...
- how to make Automatic cut off 12 volt battery charger NE555 SA555 - SE555Features■ Low turn-off time■ Maximum operating frequency greater than500 kHz■ Tim...
- FM RADIO BEYTSEL Fm Radio Receiver 4 TransistorsFm Radio Receiver 4 TransistorsHere is a very simple and effective ci...
- Flip Flop NEW Flip-Flop CircuitFLIP-FLOPThere are electronic elements whose outputs are stable in two ways with th...
- A Single Battery to Drive Your 5V Loads, Using a 1.2A 96%-Efficient DC to DC Boost Converter The rated voltage of single-cell batteries (such as Lithium-ion/Polymer) is below 5V, which is unsui...
- -NE555 Led Flasher Circuit NE555 LED FLASHER CIRCUITDESCRIPTIONThe 555 monolithic timing circuit is a highly stable controller ...
- How to make powerful inverter 12v to 220v , sine wave , irfz44n How to make powerful inverter 12v to 220v , sine wave , irfz44nThe SG3525A series of pulse width mod...
- -LM7812 Voltage Regulator LM7812 VOLTAGE REGULATORVIN = MIN 15V DCVOUT = 12V DCThe LM340 and LM7805 Family monolithic 3-termin...
- High Power DC to Dc Step Up Boost converter 0-30v Adjustable High Power DC to Dc Step Up Boost converter 0-30v AdjustableThe LM7812 is a three-pin positive volta...
- Police_Light POLICE LIGHTAre you ready for the police lights?As you can see, I made the police lights in the circ...
- Metal Detector METAL DETECTOR Metal detectors work Metal detectors work by transmitting an electromagnetic field fr...
- Basic current constant or current regulator using 7805 7805I am going to show the working of a constant current battery charger circuit. They use a few com...
- 3- DC Motor Speed Control Circuit DC Motor Speed Control CircuitYou will be able to control the speed of your engine much more easily ...
- Automatic Fading ON and OFF Circuit using BC847, BC557, Capacitor and Resistor Automatic Fading ON and OFF Circuit using BC847, BC557, Capacitor and Resistor When energized with +...
- 1- 24V Battery Level Indicator 24V BATTERY LEVEL The circuit I designed is suitable for 24V batteries. You include the + and - ends...
- Simple DC voltage booster circuit Without Coil Simple DC voltage booster circuit Without CoilHello everyone,I made a simple and powerful DC to DC b...
- Soft Start Circuit BD139Description These epitaxial planar transistors are mounted in the SOT-32 plastic package. They ...
- Mosfet-Motor Driver Modul MOTOR DRIVER MODULE IRF520NFEATURES • Dynamic dV/dt rating • Repetitive avalanche rated • 175 °C ope...
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
488 0 0 -
RF Control training board for students based on ESP32 C3
652 0 2 -
Aquarius+ Computer, Standard PCB
862 0 4 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
595 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
517 0 1 -
Nintendo Famicom HVC-001 Controller Shells
618 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
574 0 4 -
COMMODORE 128 15KHz DISPLAY ADAPTER (C128 80 COLUMN ADAPTER)
780 1 5 -