Audio amplifier Arc Welder Slewmaster OPS Main V3.0 BJT or mosfets
Hi this the the second part of the audio amplifier the Greenamp v1.2 schematic this is the power audio board this design can use BJT or mosfets power semiconductors just fallow the schematic and you will figure it out no difficult to build the photo you see is actually my build, the supply voltage is from 40V DC up to 85V DC positive and negative rails, the bias adjustment is simple to do just read voltage drop on one of the emitter resistors 0.22 ohm to 26mV DC. There is a website that has more information about this design many people build this audio amplifier. The size of the PCB is 254 mm x 80 mm. I recommended to try BJT if you are not comfortable matching V-mosfets I will leave the simulation of this amp design in mosfet and BJT power audio transistors the maximum power that can deliver this design depends on the power supply you are gonna use I recomended a 800 to 950VA toroidal transformer but this design can work just fine with a 600VA toroidal transformer according to simulation can provide close to 600 watts @4 ohms but with the experience I have I will say that can provide clean 350W @4 ohms with really low THD there is a lot of good information about this deisgn here on this link from diyaudio.com
the designer is Mr. Ostripper
https://www.diyaudio.com/forums/solid-state/248105-slewmaster-cfa-vs-vfa-rumble.html
Audio amplifier Arc Welder Slewmaster OPS Main V3.0 BJT or mosfets
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(5)
- Engineer Oct 18,2023
- Engineer May 12,2023
- Аброр Abror Jun 29,2020
- Eduardo A. Passos Feb 10,2020
- W01401A Dec 09,2019
- 1 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
-
10design
-
10usability
-
10creativity
-
10content
More by Juan A. Vargas Diaz
- Automatic speaker protection with time delay, DC detect and thermal protection This is a simple circuit that can protect your expensive speakers from annoying "pop" sound that you...
- Audio amplifier Arc Welder Slewmaster OPS Main V3.0 BJT or mosfets Hi this the the second part of the audio amplifier the Greenamp v1.2 schematic this is the power aud...
- Audio amplifier IPS driver board The Greenamp V1.2 final design by Pete "Ostripper" This is a high fidelity audio amplifier driver board that can be use in other OPS power boards is be...
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
441 0 0 -
RF Control training board for students based on ESP32 C3
588 0 2 -
Aquarius+ Computer, Standard PCB
803 0 4 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
556 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
482 0 1 -
Nintendo Famicom HVC-001 Controller Shells
582 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
544 0 4 -
COMMODORE 128 15KHz DISPLAY ADAPTER (C128 80 COLUMN ADAPTER)
739 1 5 -