Oleg Oleg
RUSSIAN FEDERATION, THE • + Follow
Edit Project
Description
3D printer motherboard
1. This control board combines ramps1.4 and maga2560, use more convenient micro USB interface to flash firmware,
adopt CH330 USB communication IC
2. A4988 motor driver chip is adopted, and 16 subdivisions are adopted by default
3. Two-layer board design, length and width no more than 10 * 10cm. Economical and compact
4. Adopt xl1509 special DC-DC power chip, support 12 volt and 24 volt power input
5. The firmware can use the open source firmware Marlin, the configuration is exactly the same as ramps1.4,
can directly replace ramps1.4
6. This design part refers to the MKS MINI V2.0 3D printer motherboard.
May 19,2020
5,388 views
3D printer motherboard
This control board combines ramps1.4 and maga2560
5388
7
1
10.00 (1)
Published: May 19,2020
BOM(Bill of materials)
Purchase
Donation Received ($)
PCBWay Donate 10% cost To Author
Only PCB
PCB+Assembly
*PCBWay community is a shared platform and we are not responsible for any design issues.
Copy this HTML into your page to embed a link to order this shared project
Copy
Under the
Attribution-ShareAlike (CC BY-SA)
License.
- Comments(1)
- Likes(7)
You can only upload 1 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
Remove
It looks like you have not written anything. Please add a comment and try again.
View More
- jhevar Jun 15,2023
- Aleksandr Artamonov Jul 26,2021
- Engineer Jul 27,2020
- Engineer Jul 20,2020
- Marhaunichy Maryan Iosifovich Jun 29,2020
- Engineer Jun 24,2020
- MUSTAFA CAMBAZ May 30,2020
View More
VOTING
1 votes
- 1 USER VOTES
10.00
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Design
1/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Usability
2/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Creativity
3/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Content
4/4
-
10design
-
10usability
-
10creativity
-
10content
10.00
More by Oleg Oleg
- Development Board STM32F103RET6 Development Board Series STM32F103RET6Resources on the board3.3/5.0/12V power input/output pinReset ...
- DAPLINK and STM32 minimum system combination DAPLINK and STM32 minimum system combination, one data cable can complete the download and debugging...
- USB to RS232 This is a program verification board. The main verification content is the function of USB to RS232 ...
- ESP Air Burner The ESP downloader with Air Burnner interface uses probes instead of DuPont cables.
- Docking station USB3.1 Using GL3520 USB 3.1 HUB chip,Supports super high speed, high speed and full speed USB connection, f...
- RX5808 open source receiver 5.8g open source receiver, can receive 5.8g signal, AV video signal output. Rx5808 dual-reception fu...
- 5.8G image transmission module It can be used for AV signal audio and video wireless transmission; baby monitor; wireless camera se...
- GRBL-ESP32 esp32s 3d is suitable for GRBL and marlin software
- STM32 Sensor Node A Small STM32F103C8T6 board with all functional pins exposed. Similar to the BluePill Board except:N...
- 2.8 inch TFT touch screen The module uses a 2.8-inch TFT color LCD screen. The module is compatible with punctual atomic 2.8TF...
- LED dot matrix clock LED dot matrix electronic clock based on 51 single chip microcomputer.Based on STC15W4K series ultra...
- STM32F411Cx 401Cx minimum system + J-LINK debugger The STM32F411 / 401 microcontroller belongs to the STM32 Dynamic Efficiency series. These devices ar...
- Small passive DC constant current electronic load IntroductionA small passive DC adjustable constant current (CC) electronic load with temperature-con...
- Small jlinkV9 downloader V1.0 Adopt typec interface, stm32f205 master control, lead SWD, SWO, support virtual serial port, resista...
- IP2325 dual string lithium battery charging module Miniature charger for dual lithium batteries.Since the IP2325 does not have a charge balancing funct...
- Electronic switch The operating voltage is within 30V. Depends on the PMOS voltage.
- Power supply module NAE20S08 Is based on SY8288A / JW5068A series power supply ic Volume: 10x10x6mm Input range: 4-23vin Output: ...
- Solder paste dispenser A portable miniature intelligent electric SMT solder paste dispensing pen supports quantitative extr...
You may also like
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
426 0 0 -
RF Control training board for students based on ESP32 C3
578 0 2 -
Aquarius+ Computer, Standard PCB
789 0 4 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
545 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
472 0 1 -
Nintendo Famicom HVC-001 Controller Shells
569 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
536 0 4 -
COMMODORE 128 15KHz DISPLAY ADAPTER (C128 80 COLUMN ADAPTER)
723 1 5 -