|
KiCADKicad
|
110/220VAC Opto-Isolated Zero Cross Detector Module for DIN Rail Carrier Mount with 3.3V or 5V Output - Ideal for Arduino, ESP32/ESP8266
This module detects the zero cross point of an AC supply and outputs a 3.3V or 5V square wave signal pulse of 1ms every time the zero point is crossed. For a 50Hz supply this pulse would be sent 100 times per second. This is ideal for micro-controller projects which require accurate synchronization with the AC supply, such as for controlling triacs to perform phase-angle control for light dimming or heater control. The AC side of the circuit is optically isolated from the DC side, providing important safety and protection for the micro-controller.
The AC supply is connected to the upper terminal block, and the lower terminal block is connected to the micro-controller, sharing its DC 3.3V or 5V and ground, and sending the output signal to a designated GPIO pin to trigger an interrupt in the code.
The board features a micro-LED indicator and is designed fit into a Camdenboss DIN rail enclosure for easy mounting.
This module adds to the growing number of DIN rail based accessories for micro-controller projects, enabling a 'plug and play' approach to speed up project-building.
CAUTION- This circuit uses mains AC voltage which is hazardous and can cause ELECTRIC SHOCK or FIRE. It must be independently reviewed and certified by a qualified professional before use. The designer accepts no responsibility for assembly or use of this module in any way.
110/220VAC Opto-Isolated Zero Cross Detector Module for DIN Rail Carrier Mount with 3.3V or 5V Output - Ideal for Arduino, ESP32/ESP8266
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(25)
- Likes(9)
- Engineer Apr 07,2024
- Enrique Barajas Jan 29,2024
- Dan TStar Jan 12,2024
- Engineer Dec 24,2023
- MATHIEU CARBOU Sep 16,2023
- Surajkumar Kalsait Aug 23,2023
- audie cantrell Feb 27,2023
- Engineer Sep 26,2022
- CodyRoseman Aug 18,2022
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Dan TStar
- 110/220VAC Opto-Isolated Zero Cross Detector Module for DIN Rail Carrier Mount with 3.3V or 5V Output - Ideal for Arduino, ESP32/ESP8266 This module detects the zero cross point of an AC supply and outputs a 3.3V or 5V square wave signal...
- "Soft Start" Inrush Current Limiter for Toroidal Transformer - DIN rail mounted This simple inrush current limiter is designed to be used with a 500VA toroidal transformer to suppl...
- Panel Mounting MicroSD Card Reader Breakout Adapter I couldn't find a panel-mounting MicroSD card reader anywhere, so I decided to design one!Many micro...
- Wii Nunchuck Controller Socket Breakout The Nintendo Wii Nunchuck controller is a great input device for microcontroller projects as it uses...
- ESP32 DevKitC adapter breakout expansion (38 pin) This is a simple breakout board for the 38 pin ESP32 DevKitC. Pins are shown broken out to female pi...
- 74HC165 8-bit Shift Register Breakout Board with pushbuttons This is a quick breakout board for the 74HC165 shift register which is an 8-bit parallel-in serial-o...
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
428 0 0 -
RF Control training board for students based on ESP32 C3
581 0 2 -
Aquarius+ Computer, Standard PCB
792 0 4 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
546 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
477 0 1 -
Nintendo Famicom HVC-001 Controller Shells
573 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
538 0 4 -
COMMODORE 128 15KHz DISPLAY ADAPTER (C128 80 COLUMN ADAPTER)
725 1 5 -