1. Blog>
  2. HALO Grappleshot - Test Unit 1 Pneumatic Prototype (WIP)

HALO Grappleshot - Test Unit 1 Pneumatic Prototype (WIP)

by: Oct 04,2026 744 Views 1 Comments Posted in 3D Printing

3D printing CAD Grappleshot

Summary:       I’m building a functional HALO‑inspired grappleshot using 3D‑printed parts, pneumatic components, and a solenoid‑triggered air system. This project explores mechanical design, Fusion 360 modeling, and rapid prototyping with Creality Hyper PLA. It’s part of my STEM Regionals engineering build.

Introduction

This project is my first full electromechanical prototype of a HALO‑inspired grappleshot, designed for STEM Regionals and built under my maker brand, MindForge Mechanics. Instead of being a simple prop, this grappleshot is a functional pneumatic launcher built from 3D‑printed components, high‑pressure air hardware, and a solenoid‑controlled firing system.

The goal of Test Unit 1 is to validate the mechanical design, air path, and trigger system before integrating custom PCBs in future versions.


Video here!

https://www.crealitycloud.com/post-detail/6ac471907


Project Overview

The grappleshot uses a combination of 3D‑printed parts, stainless‑steel fittings, and regulated HPA air to launch a tethered hook. Every major component — the barrel halves, internal rails, latch system, hook housing, and shell — was modeled in Fusion 360 and printed using Creality Hyper PLA.

This prototype focuses on:

  • mechanical structure
  • pneumatic pressure control
  • solenoid‑triggered firing
  • tether and reel planning
  • early electronics routing

Future versions will include custom PCBs for motor control, sensors, and optional LED indicators.


3D Printed Components

All printed parts were made using Creality Hyper PLA (black) for strength and clean surface finish. Key printed components include:

  • Barrel halves with internal guide rails
  • Hook housing and tether mount
  • Shell sections with mechanical ribs
  • Internal support brackets
  • Solenoid mounting block
  • Regulator and hose stabilizers
  • Trigger housing (mechanical version)

These parts were printed with:

  • 0.2mm layer height
  • 3–4 walls
  • 20–40% infill depending on stress zones

Cooling optimized for dimensional accuracy


Pneumatic System (Back → Front)

The air system is the core of the grappleshot’s functionality. Test Unit 1 uses a regulated HPA setup to safely control launch pressure.

Air Path Chain

Maddog Aluminum HPA Tank (26ci/3000psi)

↓

HPA Low Pressure MR Reg GEN2 Micro Regulator (20–200psi)

↓

PTFE Thread Seal Tape

↓

TITAN Ultraflex Hose – 1/4" NPT, 36", 6,525psi

↓

SNS DC12V Brass Solenoid Valve (Normally Closed)

↓

ChillWaves 304 Stainless Steel Nipple – 1/4" NPT, 10"

This chain delivers controlled low‑pressure air to the solenoid, which acts as the electronic trigger for firing.


Electronics (Early Stage)

Test Unit 1 uses simple wiring to power the solenoid:

  • 22‑gauge wire
  • Electrical tape for insulation
  • Basic switch for manual activation
  • Future versions will include:
  • motor driver PCB
  • trigger sensor PCB
  • power regulation PCB
  • optional LED status indicators
  • optional wireless module

These PCBs will be designed specifically to fit inside the grappleshot’s internal cavity.


Tether & Reel System

The hook is attached using:

  • fishing line or paracord
  • 6mm rods
  • 6mm bearings
  • small gears for reel planning

The reel system is not fully implemented in Test Unit 1, but the mechanical layout is prepared for future motorized retrieval.


Bill of Materials (BOM)


Air System

  • Maddog Aluminum HPA Tank – 26ci/3000psi
  • HPA Low Pressure MR Reg GEN2 Micro Regulator
  • PTFE Pipe Sealant Tape
  • TITAN Ultraflex Hose – 1/4" NPT, 36", 6,525psi
  • SNS DC12V Brass Solenoid Valve – 2W025‑N08
  • ChillWaves 304 Stainless Steel Nipple – 1/4" NPT, 10"

3D Printing

  • Creality Hyper PLA (Black)
  • Fusion 360 CAD models
  • Printed barrel, shell, rails, latch, mounts

Electronics

  • 22‑gauge wire
  • Electrical tape
  • Basic switch
  • DC power source

Mechanical

  • Fishing line or paracord
  • 6mm rods
  • 6mm bearings
  • Assorted gears


Future Plans

Test Unit 2 will introduce:

  • custom PCB integration
  • motorized reel system
  • improved shell design
  • pressure‑optimized barrel geometry
  • optional LED indicators
  • full documentation for STEM Regionals


Closing

This project represents the first major step toward a fully functional electromechanical grappleshot for STEM Regionals. PCBWay’s community and resources have been a huge help in pushing my engineering skills forward, and future versions will rely heavily on PCBWay’s PCB fabrication and assembly services.

Thanks for supporting young makers and helping projects like this come to life.


Support me at https://crealitycloud.com/user/6745400244/profile


Components
Maddog Aluminum HPA Tank – 26ci/3000psi
Maddog
x 1
HPA Low Pressure MR Reg GEN2 Micro CO2 Regulator Adjustable with US 2202 Foster Output 20psi to 200p
‎huizhoushiyouyankejiyouxiangongsi
x 1
PTFE Pipe Sealant Tape
D-NYX
x 1
TITAN FITTINGS | FA-UFW4-NPT-NPTX-36 Inch | Assembly: 1/4" Ultraflex Hose with 1/4" Male NPT x 1/4"
Titan Fittings
x 1
SNS 1/4"NPT DC12V Brass Electric Solenoid Valve Normally Closed Water, Air, Diesel 2W025-N08/DC12V
China SNS Pneumatic Co.,Ltd
x 1
ChillWaves 304 Stainless Steel Pipe Fitting, Nipple Cast Pipe 1/4" NPT Male x 1/4" NPT Male Thread 1
ChillWaves
x 1
Creality Hyper RFID PLA Filament 1.75mm 1KG, Black, 1-Pack
Creality
x 1
Fusion 360 CAD models
x 1
Printed barrel, shell, rails, latch, mounts
x 1
TUOFENG 22 AWG 2 Conductor Wire, 100 ft Red Black PVC Cable for LED
TUOFENG
x 1
3M Scotch Super 33+ Electrical Tape, 3/4 in x 52 ft, 1 Roll, Black
3M
x 1
STARELO 5pcs 12mm Momentary Push Button Switch Black Shell with pre-Wiring, IP65 Waterproof Push But
STARELO
x 1
Talentcell Rechargeable 12V 6000mAh/5V 12000mAh DC Output Lithium ion Battery Pack for LED Strip/CCT
Shenzhen Yabo Power Technology Co., Ltd.
x 1
RIKIMARU Braided Fishing Line Abrasion Resistant Superline Zero Stretch&Low Memory Extra Thin Diamet
Rikimaru
x 1
6mm x 100mm 304 Stainless Steel Round Rod, Metal Solid Shaft Rods for Industry, Metal Working Hobbie
MewuDecor
x 1
MR126-2RS 20 PCS Deep Groove Ball Bearing 6×12×4mm Double Blue Rubber Sealed Ball Bearing Chrome Ste
FOCMKEAS
x 1
Assorted gears
x 1
Solder
WYcYcW
x 1
Schematic and Layout
CAD-Custom parts and enclosures
Join us
Wanna be a dedicated PCBWay writer? We definately look forward to having you with us.
  • Comments(1)
Upload photo
You can only upload 5 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
    Table of Contents
    Back to top